mopdf.com

NORMAL OPERATION7Turn System On/OffThe OFF button is used to turn the system both on and off.HeatingTo select heating, press the red HEAT button.Heating is confirmed when the red LED adjacent to the red HEAT button is lit. Heating isoperating when the red LED is gradually pulsing on and off. (The LEDs can be turned off.For details, see ADVANCED SETUP – LIGHTING on page 30.) The heating temperature willappear in the lower right screen with the text,“HEAT AT.”Auxiliary HeatAuxiliary heat is staged electric heating included with many heatpump systems. Auxiliary heat is automatically activated by the system when it’s too cold for the heat pump to effectively heat yourhome. Auxiliary heat operation is confirmed when the red LEDadjacent to the red HEAT button is lit, gradually pulsing on, thenoff. (The LEDs can be turned off. For details, see ADVANCEDSETUP – LIGHTING on page 30.) The text, “AUXILIARY HEATACTIVE” will appear below the room temperature.Emergency HeatEmergency heat is staged electric heating included with manyheat pump systems. Emergency heat is activated either when theheat pump has malfunctioned and heating is required, or whenthe homeowner manually activates emergency heat. Emergency

NORMAL OPERATION8heat is manually activated by pressing the red HEAT button forfour seconds. To activate Emergency Heat, press the red HEATbutton for four seconds. If your system is a heat pump withelectric heat, then the display will show the three choices:SYSTEM IN CONTROL (the system will choose the type andamount of heat needed for conditions)HEAT PUMP ONLY (only the heat pump will be used for heating)ELECTRIC HEAT ONLY (only electric heat will be used forheating)If your system is a Hybrid Heat system (heat pump with gas oroil furnace), then the display will show the three choices:HYBRID HEAT (the system will choose the type and amount ofheat needed for conditions)FURNACE ONLY (only the furnace will be used for heating)HEAT PUMP ONLY (only the heat pump will be used for heating)Scroll the highlight to your choice using the scroll button underthe door, then press the left side button to save your selectionand exit.To deactivate Emergency Heat, press the red HEAT button for fourseconds and choose SYSTEM IN CONTROL or HYBRID HEAT,depending on your type of heating equipment.

NORMAL OPERATION9CoolingTo select cooling, press the blue COOL button.Cooling is confirmed when the blue LED adjacent to the blue COOL button is lit. Cooling isoperating when the blue LED is gradually pulsing on and off. (The LEDs can be turned off.For details, see ADVANCED SETUP – LIGHTING on page 30.) The programmed coolingtemperature will appear in the lower right screen with the text,“COOL AT.”AutoThe AUTO function allows your Infinity Controlto automatically switch between heating andcooling operation to maintain your comfort during transitional heating and cooling seasons.To select AUTO operation, press the red HEATand blue COOL buttons simultaneously. The redand blue LEDs will light up, and both heatingand cooling temperatures will be displayed.Adjust Heating TemperatureThe Infinity Control allows you to adjust your indoor temperatureat any time, overriding your programmed settings.1 Press the red HEAT button. Heating is confirmed when thered LED adjacent to the red HEAT button is lit.

NORMAL OPERATION102 Press the ZONE button until the name of the zone you wishto control appears on the upper left screen. Selecting “ALLZONES” allows you to select one temperature for the entirehome. Press the ZONE button for three seconds to activatethe “ALL ZONES” features.3 Use the TEMP ( \-) button to select your desired temperature,which will be displayed on the lower right. An override time willbe displayed on the lower left. Please note an override time willnot appear if programming has been turned off.4 You can change the override time in 15-minute increments bypressing the TIME ( \-) button until the desired override time isselected.- OR Press the HOLD button to override the schedule indefinitely.Adjust Cooling Temperature1 Press the blue COOL button. Cooling is confirmed when theblue LED adjacent to the blue COOL button is lit.2 Press the ZONE button until the name of the zone you wish tocontrol appears on the upper left screen. Selecting “ALLZONES” allows you to select one temperature for the entirehome. Press the ZONE button for three seconds to activatethe “ALL ZONES” feature.3 Use the TEMP ( \-) button to select your desired temperature,which will be displayed on the lower right. An override timewill be displayed on the lower left. Please note an overridetime will not appear if programming has been turned off.4 You can change the override time in 15-minute incrementsby pressing the TIME ( \-) button until the desired overridetime is selected.

NORMAL OPERATION11- OR -Press the HOLD button to override the schedule indefinitely.Adjust Fan SpeedThe Infinity Control offers the benefit of customized fan speedsduring continuous fan operation. Fan speeds can be individuallyselected for each zone as well.1 Press the ZONE button until the name of the zone you wishto control appears on the upper left screen. Selecting “ALLZONES” allows you to change fan speed for the entire home.Press the ZONE button for three seconds to activate the“ALL ZONES” feature.2 Press the FAN button to adjust the fan speed between LOW,MEDIUM, HIGH or AUTO airflow. OFF is also a selectionwhen the system has been turned off at the Infinity Control.Your fan speed selection will only apply to the displayed zone.Hold Current TemperaturePress the HOLD button to override the program and maintain the current indoor temperature set point(s) indefinitely.To revert back to your programmed comfort schedule, press theHOLD button again.NOTE: HOLD is not available if programming has been turned off.Also, if you switch from HOLD to either VACATION or UNOCCUPIED, thesystem will revert back to HOLD when those functions are cancelled.

NORMAL OPERATION12Unoccupied Function & SettingsUNOCCUPIED allows you to instantly set the system for energysaving operation.1 To select UNOCCUPIED operation, press the HOLD buttonfor three seconds. UNOCCUPIED text will be displayed.2 To take your system out of UNOCCUPIED mode, press theHOLD button for two seconds.Details for selecting UNOCCUPIED temperature, humidity and fansetting defaults are provided in the ADVANCED SETUP section ofthis manual, page 34.Vacation Function & SettingsVACATION operation conserves energy whileyou are away and ensures a comfortable homeupon your return.1 Flip down the door near the base of theInfinity Control.2 Press the VACATION button.3 Use the TEMP ( \-) button to select the desired temperaturefor VACATION operation.4 Use the TIME ( \-) button to select the number of days forVACATION operation as seen in lower left corner of screen.5 Press the VACATION button to start VACATION operation.6 You will be prompted to start VACATION operation. Press theRIGHT button for YES or press the LEFT button for NO.Note: You have up to 15 minutes to make changes to the temperature or duration after VACATION has been activated. Anychanges made after the 15 minute period will be treated as atemporary override to vacation settings.

NORMAL OPERATION137 The system will automatically revert back to its normal operation after the selected number of VACATION days has expired.- OR To cancel VACATION operation at any time simply press theVACATION button. You will be prompted to cancel VACATIONoperation. Press the RIGHT button for YES or press the LEFTbutton for NO.Details for selecting default temperature, humidity, and fan settings for VACATION are provided in the ADVANCED SETUP sectionof this manual, page 33.Check System StatusThe system status function allows you to view detailed informationabout the system’s status.1 Press and hold the RIGHT button for two seconds to check:- Equipment status- Accessory status- Current humidity- Target humidity2 Press the RIGHT button again (from theSTATUS screen) for zoning status.3 Press the RIGHT button again to return to the main screen.- OR The status screen will automatically revert back the mainscreen after 60 seconds.

NORMAL OPERATION14Accessory StatusThe accessory status screen allows you to check the approximateusage of your mechanical or electronic air cleaner, humidifier pad,and UV lamps before routine maintenance is required. Theaccessory status screen also shows your servicing dealer’s nameand phone number. You may also reset the usage indicators foryour accessories from this screen.1 Press and hold the LEFT button for two seconds to show thestatus of:- Air filter (FILTER)- Humidifier pad (HUM. PAD)- UV Lamps2 Press the RIGHT button to exit.Resetting Accessory Usage IndicatorAfter an air filter, humidifier pad, or UV Lamp has been replacedor cleaned, you may need to manually reset the percent usedindicator for the respective accessory.1 Press and hold the LEFT button to access the ACCESSORYSTATUS screen.2 Use the SCROLL button to highlight the accessory you wishto reset.3 Press the RIGHT button to reset the selected accessory.4 Press the LEFT button to exit.- OR 5 Continue to reset accessory usage indicators as desired.

NORMAL OPERATION15Accessory Maintenance Pop-Up MessagesAccessory Pop-Up messages remind you when it’s timefor accessory maintenance. There can be up to five messages,depending on the accessories installed with your system:- Replace UV Lamps- Change Humidifier Pad- Clean Air Filter - EAC- Clean or Replace Air Filter- Clean Ventilator FilterREMIND LATER: Pressing the LEFT button to selectREMIND LATER will cause the accessory status message to reappear in seven days. The message will not reappear at the end ofthe seven-day period if the usage indicator has been reset.DISMISS NOTICE: Press the RIGHT button to DISMISS NOTICE andreset the accessory maintenance reminder. The reminder willreappear at the next maintenance cycle.The maintenance cycle for the humidifier, UV lamp and EAC isbased on time and may be set by your installer. The defaults areas follows:EAC:3 months of operationHumidifier:12 months of operationUV Lamp:12 months of operationVentilator Filter:3 months of operationThe maintenance cycle for MEDIA or EAC MEDIA is based onactual airflow restriction which is automatically detected by thesystem.

NORMAL OPERATION16Service Pop-Up MessagesService Pop-Up messages remind you when it’s time for routineequipment maintenance or if the system has malfunctioned.ROUTINE MAINTENANCE RECOMMENDED: This pop-up appearswhen seasonal maintenance should be performed to maintainoptimum performance of your system. Press the RIGHT button toDISMISS NOTICE and reset the maintenance reminder. Thereminder will not reappear until the routine maintenance timer hasexpired (default 12 months). The reminder will not appear if it hasbeen turned off by the installer.SYSTEM MALFUNCTION: This pop-up appears when the systemhas detected an equipment failure. Press the RIGHT button toDISMISS NOTICE. The system may continue to operate, howevertotal system shutdown could occur at any time. It is highly recommended that you contact your dealer immediately. The pop-up willreappear in 24 hours if the equipment failure has not been corrected.Keyboard Lock-OutYou can lock the Infinity Control buttons to help avoid inadvertentchanges to your settings.Keyboard lock-out can ONLY be activated from the main screen.To do so, simultaneously press the ZONE and FAN buttons for twoseconds. Keyboard lock-out will be indicated by a graphic lock onthe screen.To unlock the control, simultaneously press the ZONE and FANbuttons for two seconds.

PROGRAMMABLE FEATURES,SETUP & OPERATION17BacklightingThe Infinity backlight feature makes the screen easy to read, evenat night or in low light conditions. High-intensity backlighting is activated when a button is pushed or the door at the base of the unit isopened. The backlighting will automatically turn off or revert to alower intensity constant backlighting after 10 seconds of no buttonactivity or 30 seconds after the door is opened. Backlighting willremain on throughout Programming, Basic Setup, and AdvancedSetup. Constant backlighting can be turned off or adjusted inADVANCED SETUP, page 30 in this manual.Determining Your Comfort ScheduleBefore you program the Infinity Control, take a moment to planyour comfort schedule. Each day of the week is divided into fourtime periods:- WAKE- DAY- EVENING- SLEEPYou can select a different heating and cooling temperature for eachzone and each time period, based on your daily or weekly schedule.Using the chart provided, enter a start time, heating temperature andcooling temperature. Then you can use this chart when you beginprogramming. You may want to create a similar chart for each zone inyour home.

PROGRAMMABLE FEATURES,SETUP & OPERATION18WAKEDAYEVENINGSLEEPTime / HT / CL Time / HT / CL Time / HT / CL Time / HT / CL Monday////////Tuesday////////Wednesday ////Sunday////////Programming Your Comfort ScheduleThe Infinity Control allows you maximum flexibility in creating a comfortschedule that best matches your lifestyle. You can choose to keep itsimple with the same schedule every day you can create one schedulefor the work week and one for the weekend or, you can make everyday different. Instructions for programming this control are detailed onthe pages that follow.NOTE: You can quit the programming process at any time by simplypressing the SCHEDULE BUTTON or closing the door at the bottomof the control. You will be prompted to either save your changes orto ignore the changes using the RIGHT or LEFT buttons.One Schedule for All DaysYou can create one schedule for all seven days of theweek using the ALLDAYS screen.1 Flip down the door at the bottom of the control.2 Press the SCHEDULE button to access theschedule screen.

PROGRAMMABLE FEATURES,SETUP & OPERATION193 Press the ZONE button until the name of the zone you wish toprogram appears on the upper left screen. Selecting “ALLZONES” allows you to create one schedule for the entire home.4 If the text “ALLDAYS” appears at the top of the screen, you areready to start.- OR Press either the LEFT or RIGHT button repeatedly as necessaryuntil “ALLDAYS” is displayed. The WAKE time period will be highlighted.5 Using the TIME ( \-) button, set the start time for this timeperiod.6 Press the red HEAT button. Heating temperature will beginflashing.7 Set the heating temperature using the TEMP ( \-) button.8 Press the blue COOL button. Cooling temperature will beginflashing.9 Set the cooling temperature using the TEMP ( \-) button.10 Use the SCROLL button to highlight the next period, thenrepeat steps 5 – 9 to select settings for DAY, EVENING andSLEEP.11 Exit the scheduling mode by either closing the door or pressingthe SCHEDULE button.- OR 12 To create a custom schedule for the remaining zones, press theZONE button to select the next zone you wish to program.Then, repeat steps 4 - 10 in this section.

PROGRAMMABLE FEATURES,SETUP & OPERATION2013 To create an identical schedule for another zone, skip ahead tothe Copying a Zone Schedule section in this manual, page 24.NOTE: A default set of heating and cooling setback temperatures, called UNOCCUPIED settings, may be activated bypressing the HOLD button. “UNOCC” will appear in place of“PERIOD” when the unoccupied settings have been activated.UNOCCUPIED setting defaults can be changed in ADVANCEDSETUP, page 34.Weekdays ScheduleYou can program one schedule for Monday through Friday using theWEEKDAYS screen.1 Flip down the door at the bottom of the control.2 Press the SCHEDULE button to access the schedule screen.3 Select the zone you want to program by pressing the ZONE button until the correct zone name appears on the upper left screen.Selecting “ALL ZONES” allows you to create one WEEKDAYSschedule for the entire home.4 If the word “WEEKDAYS” appears at the top of the screen, you areready to start. If not, press either the LEFT or RIGHT button asnecessary until “WEEKDAYS” is displayed. The WAKE time periodwill be highlighted.5 Using the TIME ( \-) button, set the start time for this time period.6 Press the red HEAT button. Heating temperature will begin flashing.7 Set the heating temperature using the TEMP ( \-) button.8 Press the blue COOL button. Cooling temperature will beginflashing.9 Set the cooling temperature using the TEMP ( \-) button.

PROGRAMMABLE FEATURES,SETUP & OPERATION2110 Use the SCROLL button to highlight the next period, then repeatsteps 5 – 9 to select settings for DAY, EVENING and SLEEP.11 Exit by pressing the SCHEDULE button or closing the door.- OR 12 To create a WEEKDAYS schedule for the remaining zones, pressthe ZONE button to select the next zone you wish to program.Then, repeat steps 4 – 10 in this section.- OR –13 Begin entering your WEEKEND schedule by pressing the RIGHTbutton and following the Weekend Schedule instructions (thenext section in this manual).Weekend ScheduleYou can program an identical schedule for Saturday and Sundayusing the WEEKEND screen.1 Flip down the door at the bottom of the control.2 Press the SCHEDULE button to access the schedule screen.3 Select the zone you want to program by pressing the ZONEbutton until the correct zone name appears on the upper leftscreen. Selecting “ALL ZONES” allows you to create one WEEKEND schedule for the entire home.4 If the word “WEEKEND” appears at the top of the screen, youare ready to start. If not, press either the LEFT or RIGHT buttonas necessary until WEEKEND is displayed. The WAKE timeperiod will be highlighted.5 Using the TIME ( \-) button, set the start time for this period.6 Press the red HEAT button. Heating temperature will beginflashing.

PROGRAMMABLE FEATURES,SETUP & OPERATION227 Set the heating temperature using the TEMP ( \-) button.8 Press the blue COOL button. Cooling temperature will beginflashing.9 Set the cooling temperature using the TEMP ( \-) button.10 Using the SCROLL button to highlight the next period, repeatsteps 5 – 9 to select DAY, EVENING and SLEEP.11 Exit by pressing the SCHEDULE button or closing the door.- OR 12 To create a WEEKEND schedule for the remaining zones, pressthe ZONE button to select the next zone you wish to program.Then, repeat steps 4 – 10 in this section.- OR 13 Begin entering a separate schedule for individual days bypressing the RIGHT button and following the instructions in theDaily Schedule (the next section in this manual).Daily ScheduleYou can program a different schedule for each day of the week byusing the SUNDAY, MONDAY, TUESDAY, WEDNESDAY, THURSDAY,FRIDAY and SATURDAY screens.1 Flip down the door at the bottom of the control.2 Press the SCHEDULE button to access the schedule screen.3 Select the zone you want to program by pressing the ZONEbutton until the correct zone name appears on the upper leftscreen. Selecting “ALL ZONES” allows you to simultaneouslyprogram one day across all zones.4 If the word “SUNDAY,” “MONDAY,” “TUESDAY,” “WEDNESDAY,”“THURSDAY,” “FRIDAY,” or “SATURDAY” appears at the top of thescreen, you are ready to start.

PROGRAMMABLE FEATURES,SETUP & OPERATION235 If not, press either the LEFT or RIGHT button repeatedly asnecessary until the day of the week you want to select isdisplayed. The WAKE period will be highlighted.6 Using the TIME ( \-) button, set the start time for this timeperiod.7 Press the red HEAT button. Heating temperature will beginflashing.8 Set the heating temperature using the TEMP ( \-) button.9 Press the blue COOL button. Cooling temperature will beginflashing.10 Set the cooling temperature using the TEMP ( \-) button.11 Using the SCROLL button, highlight the next time period, andrepeat steps 5 – 9 to select settings for DAY, EVENING andSLEEP.12 Repeat steps 5 – 11 in this section for each day you would liketo schedule or use the COPY DAY function.13 Exit by pressing the SCHEDULE button or closing the door.Copy D

Pop-up Messages Your Infinity Control provides important and useful maintenance and service reminders via pop-up messages on the display. Accessory Maintenance Reminders:An accessory reminder lets you know when it’s time for maintenance of your air filter, humidifier pad, UV lamp or venti