Transcription

Bee*R Ignition Rev Limiter Fitting (English Instructions)Congratulations on your purchase of the Bee*R Rev Limiter! Please use the followinginstructions to properly install your Bee*R product.Translated with permission from Bee*R for Tuned Japan by Kenji Bou

Please read this literature in its entirety before you start to perform the installation toensure that you get the job done correctly and safely.It is strongly recommended that you have a certified automotive electrician to performthe installation of this product.Before going any further, please note:***NOTE***These instructions are for the Type B rev limiters. For Honda applications please useType H or H2 rev limiters.Safety:A. For safe use, read, understand and consent to the safety notes.B. Only install when the vehicle’s engine condition, performance and problems arewell known.C. It not recommended using this product on a car that is not listed in the notedvehicle applications. This also goes for cars that do have a listed application but has adifferent engine not listed in the noted vehicle applications.D. Please acknowledge that problems that may occur due to improper installation,improper use, not fully understanding the instruction manual, or other unstatedproblem(s) as a result of installing this product is not the responsibility of Bee*R orBee*R authorized agents in any way, form or fashion.E. This product is an accessory used to improve performance, and it must be usedaccordingly (please see note D).F. Due to the nature of racing and the use of the product, all sales are final and theend-user accepts all risks involved in using this product. All returns must beauthorized and inspected by Bee*R in any case where bad craftsmanship is suspected.We do this due to the amount of fakes that are in production by counterfeit parties.Just because it says Bee*R doesn’t mean it is a Bee*R product. Only Bee*R canascertain whether the product is genuine. Bee*R authorized agents must forwardreturned Bee*R products to Bee*R and cannot make any assumptions nor takeaction(s) without consent from Bee*R. If you purchased the product from anauthorized Bee*R agent, your item has already been verified as authentic and will bereturned to Bee*R for review and determination of course of action.***WARNINGS***A. Ignoring the WARNINGS may lead to accidental death of driver, passengers or3rd parties.Translated with permission from Bee*R for Tuned Japan by Kenji Bou

B. Under no circumstances should the product be used in any other way than specifiedin the manual.C. The product cannot be guaranteed to perform in ways it was not intended to.Misuse of this item may lead to engine malfunction, injury or death.D. If strange noises or smells occurs at any time, discontinue use immediately toprevent electric shock, fire and/or damage to electrical components.E. Do not use this product other than what it was designed for. If used other thandesigned for, loss and damage caused by or to customer and/or third parties mayoccur.F. If this product is installed in a non-stable environment, this product may interferewith normal driving.G. If the product becomes a hindrance or interferes with driving, please discontinueuse.H. Please install only after removing negative terminal of the battery.I. When the connector is disconnected, do not pull on the harness.J. Do not wire together with other electrical components (shared wiring). Wiring withother accessories may cause a short circuit or electrical fire.K. Do not adjust product during normal driving or travelling. If used during normaldriving, the chance of accident and danger increases.NOTES:A. Ignoring the notes and cautions may lead to physical or fatal injury due todangerous handling.B. Do not disassemble the product or modify. Doing so may lead to an electrical fire,shock or electrical damage.C. Do not install in an area exposed to heat or water. If exposed to heat or water,product will malfunction and lead to possible electrical shock, fire or vehicle damage.D. Please inspect the item regularly, and if the product appears normal, please use.E. The product is manufactured with high quality material and strict quality standards.Malfunction or decrease in performance may depend on the condition of the vehicle.It is imperative that the car be properly tuned up and maintained before installing thisproduct.F. This product must be installed by a qualified automotive technician, and ifquestions arise please contact Bee*R directly.Translated with permission from Bee*R for Tuned Japan by Kenji Bou

G. Both the customer and installer must understand and read the manual and acceptthe conditions before installing this product. Bee*R will not accept any liability orresponsibility for any damage or consequences of installing the product.H. Please make sure that you read the instruction manual before asking any questions.I. Use of this product is at customer consent. Bee*R is in no way responsible fordamage to vehicle, accidents or fatal injury due to improper use of this Bee*Rproduct. Bee*R can only warranty the craftsmanship and quality of this product. AllBee*R products will be inspected upon return before any replacement is authorized orgiven by Bee*R. This product is intended for race use only and may never be used onthe streets. All sales are final.Let’s get going!Translated with permission from Bee*R for Tuned Japan by Kenji Bou

Translated with permission from Bee*R for Tuned Japan by Kenji Bou

PART 1 (using Nissan S14 kouki as the example)1) Disconnect the negative battery cable2) Remove the trim covering the ECU in the passenger foot well (use the correct sidedepending on your model). It is recommended that you take out the passenger seat togive you more room to work.Translated with permission from Bee*R for Tuned Japan by Kenji Bou

3) With a 10 mm socket or wrench, disconnect the ECU plug and locate the correctwires using the diagram below according to your vehicle specifications. You do nothave to remove the ECU unless you feel it is necessary to do so. The pins you will useare identified in the diagram according to the engine/car type you have and arecolored to match the Bee-R wire colors. The green and yellow are already reversedon this diagram as it seems the Bee-R diagram is wrong for most cars. When the caris all back together and it won’t start, swap the green/ and yellow.CA18DET (R)S13 and S14 (zenki) use diagram N01SR20DET (R)PS13, S14 (kouki) and S15 use diagram N02Translated with permission from Bee*R for Tuned Japan by Kenji Bou

The picture below shows the wires on for N02 connection type.***ATTENTION!***The tools/items you will need to perform the electrical work, at a minimum areelectrical wire cutter and crimper and bullet connectors. These items can be found atany automotive electrical store.***CAUTION!***Do not use electroclamps. These have been known to fail.Translated with permission from Bee*R for Tuned Japan by Kenji Bou

Cut the necessary wires one at a time. Do not rush this step.Slip the bullet connector insulation onto the wire and strip the end about 10 mm toexpose the wiring.Loop the exposed wiring.Translated with permission from Bee*R for Tuned Japan by Kenji Bou

Insert the bullet connection (male or female) and crimp the connection. Repeat this foreach of the wires.Your wiring will look like this after you have completed the wiring of the Bee*R RevLimiter.PART 21) On the controller, cut the gray wire for 4 cylinder applications.Translated with permission from Bee*R for Tuned Japan by Kenji Bou

2) The option to use REV2 setting requires the white wire to be connected in-linewith the e-brake switch. You must remove the center console to do this.You will need a minimum of one meter of white wiring to do this option.Translated with permission from Bee*R for Tuned Japan by Kenji Bou

Now reconnect the ECU and the ECU plug.Reconnect the negative battery cable.3) Turn the ignition to the “ON” position and check for abnormal smells and/orsmoke. Start the car. If it won’t start, you need to swap the green and yellow wires.Replace all the trim panels. Both the Rev 1 and Rev 2 should be at position 0. Revthe car and it should cut at 2500rpm with the handbrake up or down. Change thesetting on Rev 1 to 2 and try again. With the handbrake up it should rev to 2500rpm,with it down it should now be 3500rpm. Rev 2 can be used as a launch control.Adjust Rev 1 and Rev 2 to the setting you require using the 00550060006500Translated with permission from Bee*R for Tuned Japan by Kenji Bou

9) 7000A) 7500B) 8000C) 8500D) 9000E) 9500F) 10000REV1 is the normal rev limit and REV2 is the limit when e-brake switch is engaged.GAIN sets the frequency and length of cut.4) Once you are satisfied with the settings, mount the limiter using double-sided tape.You will need to clean the surfaces the tape will be adhered to. Brake/parts cleaner isan excellent choice to remove oil and residue.5) DO NOT TRY TO ADJUST THE LIMITER “ON THE FLY”! You will riskdamaging your electronics. It is highly recommended that the Bee*R Rev Limiter beadjusted in a controlled environment.6) Enjoy!Translated with permission from Bee*R for Tuned Japan by Kenji Bou

Bee*R authorized agents in any way, form or fashion. E. This product is an accessory used to improve performance, and it must be used . Disconnect the negative battery cable 2) Remove the trim covering the ECU in the passenger foot well (use the correct side . The option to use REV2 setting requires th