Transcription
99-2001APPLICATIONSGM MULTIMULTI KITGMKIT99-2001AW-200GMKIT FEATURES DIN Head Unit w/ Equalizer ProvisionKIT COMPONENTSA) Radio Housing B) Spacer C) Equalizer Dummy Plate D) Shaft MasksACBDTOOLS REQUIRED:Phillips Screwdriver1-800-221-0932 Utility Knife Socket Wrenchwww.metraonline.com COPYRIGHT 2004-2007 METRA ELECTRONICS CORPORATIONINST-2001 - Rev. 10-11-07
VEHICLE APPLICATION CONTENTSBUICKCenturyLe SabrePark ERH2ISUZUAscenderI Series 9927Cavalier2000-200512Colorado2004-200835Cutlass SupremeEighty-Eight1995-19971994-19992728Express -199628Malibu houette2000-200419, 20S-102002-20042003-2006SilveradoSilverado Classic 2000-200532Tahoe2003-200610Grand 519, 20Venture2000-200519, OLET / GEOAvalancheMonte CarloGMCCanyonDenaliEnvoySavannaSierraSierra cALL VEHICLESKit Assembly36-37Final Assembly38Notes39
99-2001BUICK Century 1997-04 / Regal 1997 - 04Disconnect the negative battery terminal to prevent an accidental short circuit.4. Unclip top edge of panel below steering column and let hang.5. Remove (1) 9/32" screw from right side of instrument cluster andradio trim panel and remove entire panel from right to left.6. Remove (3) 9/32" screws to remove radio.Continue to kit assembly.DASH DISASSEMBLY1. Open both doors and remove end caps from both ends of dashboard.2. Open glove box, then remove (1) 9/32" screw from panel above passengerkick panel and remove.3. Remove 9/32" screws from bottom left and right of ashtray assemblyand unclip and remove.3
99-2001BUICK LeSabre 1995-99 / Park Avenue 1995-99Disconnect the negative battery terminal to prevent an accidental short circuit.DASH DISASSEMBLY1. Unsnap the climate control trim panel (from door to door) and remove (5) 9/32”4screws exposed.2. Pop out the a/c vents and remove (1) Phillips screw exposed in each vent cavity.3. Unclip the radio trim bezel and remove.4. Remove the screws securing the factory head unit and disconnect the wiring.Continue to kit assembly.
99-2001BUICK LeSabre 2000-04 / Park Avenue 2000-04Disconnect the negative battery terminal to prevent an accidental short circuit.2. Remove (2) Phillips screws from underneath steering column cover.3. Unsnap and remove steering column cover.4. Unsnap and remove instrument panel.5. Remove (2) 9/32" screws and remove radio.Continue to kit assembly.DASH DISASSEMBLY1. Open drivers door and unsnap and remove dash end cap.5
99-2001BUICK Rendezvous 2002-04Disconnect the negative battery terminal to prevent an accidental short circuit.DASH DISASSEMBLY1. Open center console and remove 2 screws at front of console opening.62. Remove liners from cup holders and storage pocket next to cup holders,then remove screws. Unsnap and remove panel.3. Remove (2) screws from bottom of radio/climate control bezel, unclipand remove.4. Remove (3) 9/32" hex head screws to remove radio.Continue to kit assembly.
99-2001BUICK Riviera 1996-99Disconnect the negative battery terminal to prevent an accidental short circuit.DASH DISASSEMBLY1. Unsnap left side panel exposing (1) Phillips screw to remove.2. Remove (1) Phillips screw and unsnap right side panel to expose(1) Phillips screw beneath panel and remove.3. Unsnap underside of overhanging dash to unsnap (6) plastic rivets andremove panel.4. Remove (5) hex head screws now exposed under overhang.5. Unsnap bottom edge of trim bezel, then while holding overhang up,unsnap and remove trim bezel by removing any necessary harnesses.6. Remove (3) Phillips screw to remove climate control.7. Remove (2) Phillips screws to remove rear support and (3) 9/32" hexhead screws to remove radio.Continue to kit assembly.7
99-2001BUICK Roadmaster 1995-96Disconnect the negative battery terminal to prevent an accidental short circuit.DASH DISASSEMBLY1. Unclip dash panel sides and remove.82. Unclip panel below steering column and remove.3. Unclip panel next to glove box on passenger side and remove.4. Remove (2) 7mm screws above instrument cluster.5. Set parking brake, turn car on, and move shifter to the lowest gear. Tilt steeringwheel down then unsnap entire instrument cluster/radio panel and remove.6. Remove (3) 7mm screws to remove radio.Continue to kit assembly.
99-2001BUICK Skylark 1996-98Disconnect the negative battery terminal to prevent an accidental short circuit.2. Under glove box and drivers knee bolster, remove (2) plastic panels byturning (2) 1/4 turn fasteners per side.3. Remove (4) 9/32" screws revealed. (2 per side).4. Unsnap panel from driver's side to passenger's side.5. Remove (3) 9/32" screws to remove radio.Continue to kit assembly.DASH DISASSEMBLY1. Remove (6) 9/32" screws inside glove box.9
DASH DISASSEMBLY99-200110CADILLAC Escalade 2003-04CHEVROLET Avalanche 2003-04Silverado 2003-04 / Suburban 2003-04Tahoe 2003-04GMC Sierra 2003-04Yukon / Denali / XL 2003-04Disconnect the negative battery terminal to prevent an accidental short circuit.1. Unsnap and remove dash bezel.2. Remove (3) 9/32" screws and remove radio.Continue to kit assembly.
99-2001CHEVROLET Blazer 2002-04 / S-10 2002-04GMC Sonoma 2000-04OLDSMOBILE Bravada 1998-011. Remove (2) 9/32" hex-head screws from the knee bolster.2. Pull down on the bolster and remove 9/32" screws exposed on the base ofthe dash trim bezel.3. Remove (1) Phillips screw above the instrument cluster.4. Unclip the dash trim bezel and remove.5. Unclip the dash trim bezel and remove.Continue to kit assembly.DASH DISASSEMBLYDisconnect the negative battery terminal to prevent an accidental short circuit.11
99-2001CHEVROLET Cavalier 2000-04DASH DISASSEMBLYDisconnect the negative battery terminal to prevent an accidental short circuit.121. Open driver door and remove fuse panel on the end of dash.2. Open passenger door and remove panel on end of dash.3. Remove (1) Phillips screw from each side exposed.4. Remove (3) screws from top of glove box liner.5. Remove (2) screws from the top-left corner of the glove box cavity.6. Remove (1) Phillips screw from the defroster duct.7. Remove the duct work and (1) Phillips screw exposed.8. Remove the dash pad and (3) Phillips screws exposed at the top of theradio trim bezel.Continue to kit assembly.
99-2001CHEVROLET Express Van 2001-02 / GMC Savanna 2001-02Disconnect the negative battery terminal to prevent an accidental short circuit.2. Unsnap radio/climate/instrument panel.3. Move shift lever to first gear position.4. Rotate panel counterclockwise to lift over steering column and remove.5. Remove (3) 9/32" hex head screws to remove radio.Continue to kit assembly.DASH DISASSEMBLY1. Unsnap and remove small trim panel below steering column.13
99-2001CHEVROLET Express Van 2003-04 / GMC Savanna 2003-04DASH DISASSEMBLYDisconnect the negative battery terminal to prevent an accidental short circuit.141. Remove (2) 10mm bolts from below knee bolster under steering columnand remove panel.2. Remove (2) 10mm bolts from panel below passenger dash air bag andremove panel.3. Remove (2) 10mm nuts from inside center pocket between power outlets.4. Unsnap and remove radio and instrument cluster panel. (May not be necessary to completely remove radio and instrument cluster panel to accessradio.)5. Remove (3) 9/32" bolts to remove radio.Continue to kit assembly.
99-2001CHEVROLET Impala 2000-04Disconnect the negative battery terminal to prevent an accidental short circuit.2. Remove (2) Phillips screws under the instrument cluster.3. Unclip the trim panel above the pedals. (It is not necessary to remove thepanel, it can be left hanging.4. Remove (2) Phillips screws from under the knee panel.5. Unclip the knee panel and remove (1) Phillips screw exposed on the rightside of the steering column.6. Unclip and remove the entire dash trim bezel.Continue to kit assembly.DASH DISASSEMBLY1. Unclip each side of the dash trim bezel (fuse access) and remove (1) Phillipsscrew exposed on each side.15
99-2001CHEVROLET Malibu 2001-03 / Malibu Classic 2004Disconnect the negative battery terminal to prevent an accidental short circuit.DASH DISASSEMBLY1. Unsnap and remove radio bezel.162. Remove (3) 9/32" hex head screws and remove radio.Continue to kit assembly.
99-2001CHEVROLET Monte Carlo 2000-04Disconnect the negative battery terminal to prevent an accidental short circuit.panel, it can remain hanging.)2. Remove (2) 9/32" screws from the knee panel and unclip the panel.3. Unsnap the driver's side fuse panel cover and remove (1) 9/32" screw.4. Open the glove box and remove (1) 9/32" screw from the upper left corner.5. Remove (3) 9/32" screws securing the factory radio and disconnect thewiring.Continue to kit assembly.DASH DISASSEMBLY1. Unclip the trim panel above the pedals. (It is not necessary to remove the17
99-2001CHEVROLET Trailblazer 2002-04Disconnect the negative battery terminal to prevent an accidental short circuit.DASH DISASSEMBLY1. Remove (2) Phillips screws inside instrument cluster.182. Remove (1) Phillips screw under climate controls to the left of the poweroutlet.3. Remove (2) 7mm hex heads from under steering column and lower thepanel. Remove (3) Phillips screws around steering wheel.4. Unsnap and remove bezel. (Use caution pulling over hazard switch.)Remove (3) 7mm hex head screws to remove radio.Continue to kit assembly.
99-2001CHEVROLET Venture 2000OLDSMOBILE Silhouette 2000PONTIAC Montana 20001. Remove the ashtray and (1) Phillips screw exposed in the ashtray cavity.2. Remove (1) Phillips screw from the cigarette lighter compartment.3. Remove (3) 9/32" hex-head screws securing the factory head unit anddisconnect the wiring.Continue to kit assembly.DASH DISASSEMBLYDisconnect the negative battery terminal to prevent an accidental short circuit.19
99-2001DASH DISASSEMBLYCHEVROLET Venture 2001-04OLDSMOBILE Silhouette 2001-04PONTIAC Montana 2001-0420Disconnect the negative battery terminal to prevent an accidental short circuit.1. Open cup holders and remove (2) Phillips 7mm screws.2. Unsnap and remove dual power outlet assembly from lower storage.3. Open lower storage door and remove (2) 7mm screws inside.4. Models with DVD - Remove DVD player and remove (2) 7 mm screws frombehind and (2) 7 mm screws near the floor.5. Remove lower storage compartment .6. Remove (2) 7mm screws (facing up) from under cup holder.7. Remove (3) 7mm hex-head screws and remove radio.Continue to kit assembly.
99-2001HUMMER H2 2003-2004Disconnect the negative battery terminal to prevent an accidental short circuit.remove box.2. Remove (4) phillips screws from hinge on console door inside consoleand remove door.3. Loosen (1) T-15 torx on forward facing side of shift lever and pull up toremove.4. Unclip cup holder/shifter trim assembly and remove.5. Remove (6) phillips screws from top of center console.6. Remove (2) phillips screws from inside pocket on back of center console,then unclip and remove. Continue to kit assembly.Continued on page 22.DASH DISASSEMBLY1. Open center console and remove (4) 9/32” screws from console box and21
99-2001HUMMER H2 2003-2004Disconnect the negative battery terminal to prevent an accidental short circuit.DASH DISASSEMBLY7.22Remove (1) 10mm bolt to right of shift lever.8. Remove (2) phillips screws from under console box on drivers side and (2)phillips screws from under console trim top on passenger side.9. Slide control assembly rearward.10. Remove (2) T-30 torx bolts from top of radio/climate control trim andunclip and remove.11. Remove (3) 9/32” screws that hold the radio in.Continue to kit assembly.continued from page 21
99-2001GMC Envoy 2002-04 / ISUZU Ascender 2003-04OLDSMOBILE Bravada 2002-04Disconnect the negative battery terminal to prevent an accidental short circuit.below dash forward of center console.2. Slide carpeted panel down and backwards to reveal (2) Phillips screws andremove.3. Unsnap radio bezel and unplug cigarette lighter and accessories.4. Remove (3) 9/32" hex head screws and remove radio.Continue to kit assembly.DASH DISASSEMBLY1. Remove (4) Phillips screws, (2) from left and (2) from right of carpeted panel23
99-2001OLDSMOBILE Achieva 1996-98DASH DISASSEMBLYDisconnect the negative battery terminal to prevent an accidental short circuit.241. Open the glove box, press inward on the walls of the glove box liner andremove the liner.2. Remove (10) torx-head screws from the glove box location.3. Remove (2) 9/32" hex-head screws under the steering column.4. Unclip the dash trim bezel.5. Remove the screws securing the factory head unit and disconnect thewiring.Continue to kit assembly.
99-2001OLDSMOBILE Alero 1999-04Disconnect the negative battery terminal to prevent an accidental short circuit.of shifter and pull upward.2. Unclip and remove shifter trim panel.3. Unclip and remove radio and climate control panel by pulling from bottom.4. Remove (3) 9/32" screws from radio and remove.Continue to kit assembly.DASH DISASSEMBLY1. Remove shift knob by using a small screwdriver to remove U-clip from front25
99-2001OLDSMOBILE Aurora 1995-03DASH DISASSEMBLYDisconnect the negative battery terminal to prevent an accidental short circuit.261. Unclip the radio trim bezel and remove.2. Remove (3) 9/32" screws securing th
Express Van 2001-2007 13,14 Impala 2000-2005 15 Malibu 2001-2003 16 Malibu Classic 2004-2005 16 Monte Carlo 2000-2005 17 S-10 2002-2004 11 Silverado 2003-2006 10 Suburban 2003-2006 10 Tahoe 2003-2006 10 Trailblazer 2002-2007 18 Venture 2000-2005 19,20 GMC Canyon 2004-2008 35 Envoy 2002-2007 23 Savanna 2001-2007 13,14 Sierra 2003-2006 10 Sonoma 2002-2004 11
