Transcription

VVDI2 - VAG User Manual

VVDI2 – VAG User ManualTable of Contents1.Document Declaration . 42.Overview . 53.4.2.1.Noun explanation . 52.2.Options . 52.3.Diagnostic Function . 52.4.Key Learn . 62.5.Special Function . 6Options . 73.1.Language . 73.2.Diagnostic parameters. 8Diagnostic Function . 94.1.Identification. 104.2.Read/Clear DTCs . 114.3.Coding . 124.4.Actuator test. 124.5.Security access . 134.6.Customer Requests . 144.7.ECU Flasher . 154.8.UDS Adaption . 164.9.Advance Measure Value. 164.10.Basic Settings . 172Ver: 1.1

VVDI2 – VAG User Manual5.4.11.Adaptation . 194.12.Measured Values . 20Key Learn . 215.1.6.4th immobilizer system . 215.1.1.4th immobilizer system – Instrument cluster . 215.1.2.4th immobilizer system – Passat /CC. 295.1.3.4th immobilizer system – Touareg/Phaeton/A8/Cayenne/Bentley . 345.1.4.4th immobilizer system – Audi A6/Q7/Allroad . 355.2.5th immobilizer system . 385.3.Key Learn . 435.4.Remote Key Adaptation . 49Special Function . 506.1.Engine control unit . 506.2.K-Line Instrument/Immobox . 536.3.Change KM . 566.4.Adapt Unit . 586.5.Component Protection . 636.6.6.5.1.Generation 1 component protection . 636.5.2.Generation 2 component protection . 66EEPROM Dump Tool . 693Ver: 1.1

VVDI2 – VAG User Manual1. Document DeclarationPlease view the following declaration carefully: VVDI2 – VAG User Manual can help you maintenance vehicles with VVDI2 device.Please DON’T used for illegal purpose, Please follow the national law VVDI2 – VAG User Manual is written by VVDI2, please DON’T used for commercialpurposes without authorize VVDI2 – VAG User Manual can help you how to use VAG software, please viewcarefully Any illegal use VVDI2 – VAG User Manual, illegal use VVDI2 device, The usershould take all risks, the company does not assume any responsibility4Ver: 1.1

VVDI2 – VAG User Manual2. Overview2.1. Noun explanationVAG: Volkswagen Group, it have many brands, such as: VW, Audi, Skoda, Seat,Porsche, Bentley, Lamborghini etcComponent security: Sometimes we call it component security bytes. Usually weuse CS to express. This data usually use in car immobilizer, ECU and keyPIN: PIN code, Login, Login code etc. It can use to login module before key learn andadapt device etcComponent protection: It’s a protection type for unit module. Many modules on AudiA4/A5/A6/A8 use this method to bind module to gateway. If you install a 2nd handmodule (has component protection) to new car, you must learn it to new vehiclebefore it work. Reset to virgin module, learn to new vehiclesLost all key: The car lost all working key, there is big different from add key withworking key. Note: before OBDII communication, you need open dangerous light,press on the brakes for several times to active OBD communication2.2.OptionsDetail can be found in chapter 3 Options Choose Language Diagnostic parameters2.3.Diagnostic FunctionDetail can be found in chapter 4 Diagnostic Function Identification Coding Actuator test Read DTCs Clear DTCs Basic settings Security access Adaptation Custom requests Measured values Advance measure values ECU Flasher5Ver: 1.1

VVDI2 – VAG User Manual2.4. 4th immobilizer system: Detail can be found in chapter 5.1 4th immobilizer system5th immobilizer system: Detail can be found in chapter 5.2 5th immobilizer systemKey Learn: Detail can be found in chapter 5.3 key learnRemote Key Adaptation: Detail can be found in chapter 5.4 Remote Key Adaptation2.5. Key LearnSpecial FunctionEngine Control Unit: Detail can be found in chapter 6.1 engine control unitK-Line Instrument/Immobox: Detail can be found in chapter 6.2 K-Lineinstrument/immoboxChange KM: Detail can be found in chapter 6.3 change KMAdapt Unit: Detail can be found in chapter 6.4 adapt unitComponent protection: Detail can be found in chapter 6.5 component protectionEEPROM dump Tool: Detail can be found in chapter 6.6 EEPROM dump tool6Ver: 1.1

VVDI2 – VAG User Manual3. Options3.1.LanguageSupport following languages: Chinese (Simplified) EnglishPlease manual set user language after first run program7Ver: 1.1

VVDI2 – VAG User Manual3.2.Diagnostic parametersSet diagnostics connect protocol type (PICTURE 3.1). This will only be use at diagnosticsfunction. While scan all unit, close unused protocol will enhance scan speed CAN resistor: Generally, there is impedance between CAN High PIN and CAN LowPIN. If you connect to car directly, the gateway will finish this job. But if you wantconnect on a bench or connect to unit directly, VVDI2 will finish this job as your selectvalue K-Line parameters:K-Line try baud rate sequence: Diagnostic K-Line unit have 2 different baud rates.You can set which baud rate can be test first. Some old module may need wake up byinitialize 2 times. You can try with change baud rate sequence.K-Line use OBDII PINs: Set K-Line use PIN. If select 7 PIN, it will be always try firstK-Line connect parameters: Set K-Line timer while initialize and communication(PICTURE 3.1)8Ver: 1.1

VVDI2 – VAG User Manual4. Diagnostic FunctionSupport TP2.0, UDS, KWP1281, KWP2000 protocol, It can display item detail informationwith offline database (PICTURE 4.1)(PICTURE 4.1) Show all unit: Show all support unit listGateway installation unit list: Get installed unit list from gatewayScan all unit show in list: Scan all unit list in (PICTURE 4.1), you can enhance scanspeed by set diagnostic parametersClear All DTCs: Clear all trouble codes in list unit, you need scan it firstConnect input unit: Connect the input unit directly9Ver: 1.1

VVDI2 – VAG User Manual4.1.IdentificationRead the basic information for target unit: VAG number, HW/SW version, coding,system decryption, equipment number, importer number, workshop number etc.Example: diagnostic instrument with UDS protocol (PICTURE 4.2)(PICTURE 4.2)10Ver: 1.1

VVDI2 – VAG User Manual4.2.Read/Clear DTCsRead DTCs: The read trouble codes have detail explanation; you can select Read FreezeFrame Data for the DTC environmentsClear DTCs: clear trouble codes in module (PICTURE 4.3)(PICTURE 4.3)11Ver: 1.1

VVDI2 – VAG User Manual4.3.CodingSet target unit coding, we have database for most of the module, you can change codingby select item (PICTURE 4.4)(PICTURE 4.4)4.4.Actuator testTest every small actuator in target unit, UDS protocol support selective tests, otherprotocol support sequential tests (PICTURE 4.5)(PICTURE 4.5)12Ver: 1.1

VVDI2 – VAG User Manual4.5.Security accessLogin module with PIN code, usually use before adaptation. You can complete manyuseful function with this, example: learn new key, remote control, change 2nd module (oldtype) etc ( PICTURE 4.6)(PICTURE 4.6)13Ver: 1.1

VVDI2 – VAG User Manual4.6.Customer RequestsYou can write your own commands to target unit (PICTURE 4.7)(PICTURE 4.7)14Ver: 1.1

VVDI2 – VAG User Manual4.7.ECU FlasherSupport flash ECU with original flash file: odx, frf, sgo. Update your module to newestsoftware version. For ECU flash ECU may change the power class, it depends on theflash file you use. (Base on this feature, you can change ECU from 1.8T to 2.0T withsuitable flash file). Note: Before flash ECU, you need switch ON ignition with working keyor the target module with IMMO OFF status. Of course, if the target unit is none aboutimmobilizer, there’s no limit for flash ECU (PICTURE 4.8)(PICTURE 4.8)15Ver: 1.1

VVDI2 – VAG User Manual4.8.UDS AdaptionSet new value in channel for model use UDS protocol (PICTURE 4.9)(PICTURE 4.9)4.9.Advance Measure ValueView detail measure value in target model. Mainly use for UDS protocol (PICTURE 4.10)(PICTURE 4.10)16Ver: 1.1

VVDI2 – VAG User Manual4.10. Basic SettingsComplete basic settings for target unit. If you install new module to car, usually require thisfunction to configuration the new module. Usually you need run “Security Access” first.Example: This is K-Line ECU module (PICTURE 4.11), (PICTURE 3.12)(PICTURE 4.11)17Ver: 1.1

VVDI2 – VAG User Manual(PICTURE 4.12)18Ver: 1.1

VVDI2 – VAG User Manual4.11. AdaptationComplete learn key, learn remote, learn new module etc (PICTURE 4.13). Usually you needrun “Security Access” first(PICTURE 4.13)19Ver: 1.1

VVDI2 – VAG User Manual4.12. Measured ValuesView the detail information from channel. Usually use for CAN and K-Line protocol(PICTURE 4.14)(PICTURE 4.14)20Ver: 1.1

VVDI2 – VAG User Manual5. Key Learn5.1.4th immobilizer systemVW/Audi/Skoda/Seat/Porsche/Bentley vehicles all have 4th immobilizer car. (How to verifynew key is dealer key? Key is learned success or not? Transponder is correct or not?Car ignition switch is work fine or not? About this you can find answer for Immo status in“Key Learn - Key Learn”)Support following types:1. Instrument - CDC3217/CDC3297/CDC3272 24C322. Instrument - NEC 24C323. Instrument - NEC 24C644. Instrument - NEC 24C64 (2013-)5. Instrument– NEC 24C64 (2012 TFT color display)6. Instrument– NEC 24C64 (2013 TFT color display)7. Instrument– NEC35xx8. Instrument– NEC 953209. Instrument– Motorola 9S12XHZ512(Golf6 MM7 – 2011)10. Instrument– NEC 95320(Johnson Controls)11. Instrument– NEC 95320(JCI – 2013 Bora/Jetta)12. Instrument– Visteon13. VW Passat B6/B7/CC Key Learn14. Touareg/Phaeton/A8/Cayenne/Bentley 4th immobilizer15. Audi A1 – NEC 24C6416. Audi A3/TT/R8 – CDC3217/3297 24C3217. Audi A4 – instrument Crypto RB4 (2001 )18. Audi A4 –instrument Crypto RB8 (2004 )19. Audi A6/Q7/Allroad – EZS-Kessy20. Audi Q35.1.1.4th immobilizer system – Instrument clusterSupport function: read/write EEPROM, read/write FALSH (part support), change KM, addkey, read START/STOP key data etcVVDI2 – VAG provide auto detect cluster login type. 4th immobilizer cluster useMEGAMOS 48 transponder as key, see the following explanation: Diag: We can auto detect cluster login type here, support CAN and UDS protocol. Ifauto detect error, please send diagnostic results to your dealer by enter unit 17instrument cluster (PICTURE 5.1)21Ver: 1.1

VVDI2 – VAG User Manual (PICTURE 5.1)Read EEPROM/FLASH: Read EEPROM or FLASH via OBDII. Read FLASH is onlypart support, not support by all type (PICTURE 5.2)(PICTURE 5.2)Save File /Load File :Save data read by OBDII (EEPROM, FALSH, Immo dataetc) / Load file to bufferRead Immo Data/Write Immo Data: Read immo data from cluster/ Write immo datato cluster. Immo data is very important, you can prepare a dealer key with “Key Le