mopdf.com

Printer Driver Installation on Windows 8 (Add Printer) You will now see your printer listed under a list ofavailable Ithaca printers to select. Select yourprinter, and then click the Next button. Note: If you have a POSjet 1500/POSjet1000/BANKjet 1500 printer, select SE1500 for yourprinter. Note: If you have a Series 50, Series 70, Series80/80PLUS, Series 90/90PLUS, or Series 150printer, move on to the next page.

Printer Driver Installation on Windows 8 (Add Printer) For the Printer name, leave it as it is, or name itwhatever you would like, then click Next.

Printer Driver Installation on Windows 8 (Add Printer) Select Do not share thisprinter, then click Next.

Printer Driver Installation on Windows 8 (Add Printer) Click the Finish button Note: Do not click the “Print a test page” button.Skip this for now.

Printer Driver Installation on Windows 8 (Add Printer) After installing the printer, go to your Devices andPrinters page, and right click on your printer andselect Printer Properties, then select the “Ports” tab,and uncheck the “Enable bidirectional support”checkbox, and then click Apply and then OK.Note: If this is checked, it can cause the printer toprint intermittently, or not print at all, and it ischecked by default after installing the printer, somake sure to uncheck it. Click on the General tab, and under the Generaltab, click the “Print Test Page” button to print aWindows Test Page, and the Windows Test Pageshould print out on your printer. Your printer is nowinstalled and ready to use.

Visual Quick Start GuidePrinter Driver Install on Windows 7

Printer Driver Installation on Windows 7 (Add Printer)Download Printer Driver from Transact Web Sitewww.transact-tech.com1.First make sure your printer is powered on and connected to your PC. Then, download our Windows 7 driver for yourrespective printer model by going to our Service & Support section on our website at http://www.transact-tech.com/serviceand-support, then click on your printer model, and under “Drivers” download the Windows Driver for “Windows Server2003/2008, XP, Vista, 7, or 8 32-bit or 64-bit systems” at the top of the page.Note: If you are installing a Series 50, Series 70, Series 80/80PLUS, Series 90/90 PLUS, or a Series 150 printer,unfortunately we don’t have any Windows 7 drivers for these printers and don't plan on developing any since they are ourolder printers. Instead you want to Install a Generic/Text Only driver, which is included in Windows 7, and will allow you toprint. Please skip the steps below if you have a Series 50, Series 70, Series 80/80PLUS, Series 90/90PLUS or Series 150printer, and follow the instructions on the next page.2.Click on the Download link on the right hand side, and then click the Save button, and save the .zip file to your Desktop.3.On your Desktop you will then see the .zip file for the driver for your respective printer model. Double click this file, andunzip and extract the driver, then proceed with the following instructions to install the driver.

Printer Driver Installation on Windows 7 (Add Printer) Click your Start Menu in the lower left hand cornerof your screenSelect Device and PrintersClick the Add a printer button

Printer Driver Installation on Windows 7 (Add Printer) Select Add a local printer

Printer Driver Installation on Windows 7 (Add Printer) Select Use an existing port and select your portfrom the drop down menu, and then click Next. Ifyou have a Parallel Printer select LPT1, if you havea Serial Printer select COM1, and if you have aUSB Printer select the proper USB port. Note: In most cases if you have a USB printer, youwant to select USB001 as your port as this will bethe only USB port listed. If you have multiple USBports to choose from (USB002, USB003, etc.), runour USBPortView.exe utility, which can be found inthe Utilities folder of our Windows driver. After yourun the utility, look for the USB port that has“Transact” listed for the Manufacturer. So, forexample, if USB003 has “Transact” listed as theManufacturer, that is the port you will need tochoose in the Add Printer Wizard Note: If installing an Ethernet Printer, select“Create a new port”, then select Standard TCP/IPport for “Type of port”. You will need the IP addressto add the TCP/IP port.

Printer Driver Installation on Windows 7 (Add Printer) Note: If you have a Series 50, Sereies 70,Series 80/80PLUS, Series 90/90PLUS, orSeries150 printer, select Generic for theManufacturer, and select Generic/TextOnly for the Printer, and then click Next.Then, skip the instructions below, and moveon to the next page. At the Select Manufacturer and PrinterWindow, click the Have Disk button, thenclick the Browse button, and go to thelocation where you extracted the driver to. Depending on what printer you are installingchoose the correct folder. For example, if you are installing an iTherm280/Epic 430/Epic 880/Ithaca 9000, openITherm-576 folder, and select theTactITherm-576.INF file. If you are installing a POSjet 1500/POSjet1000/BANKjet 1500/BANKjet 2500, selectthe IJet folder, then select the TactIJet.INFfile.

Printer Driver Installation on Windows 7 (Add Printer) After you choose the proper .INF file, click theOpen button, then click the OK button Note: If you have a Series 50, Series 70, Series80/80PLUS, Series 90/90PLUS, or Series 150printer, move on to the next page.

Printer Driver Installation on Windows 7 (Add Printer) You will now see your printer listed under a list ofavailable Ithaca printers to select. Select yourprinter, and then click the Next button. Note: If you have a POSjet 1500/POSjet1000/BANKjet 1500 printer, select SE1500 for yourprinter. Note: If you have a Series 50, Series 70, Series80/80PLUS, Series 90/90PLUS, or Series 150printer, move on to the next page.

Printer Driver Installation on Windows 7 (Add Printer) For the Printer name, leave it as it is, or name itwhatever you would like, then click Next.

Printer Driver Installation on Windows 7 (Add Printer) Select Do not share thisprinter, then click Next.

Printer Driver Installation on Windows 7 (Add Printer) Click the Finish button Note: Do not click the “Print a test page” button.Skip this for now.

Printer Driver Installation on Windows 7 (Add Printer) After installing the printer, go to your Devices andPrinters page, and right click on your printer andselect Printer Properties, then select the “Ports” tab,and uncheck the “Enable bidirectional support”checkbox, and then click Apply and then OK.Note: If this is checked, it can cause the printer toprint intermittently, or not print at all, and it ischecked by default after installing the printer, somake sure to uncheck it. Click on the General tab, and under the Generaltab, click the “Print Test Page” button to print aWindows Test Page, and the Windows Test Pageshould print out on your printer. Your printer is nowinstalled and ready to use.

Visual Quick Start GuidePrinter Driver Install on Windows Vista

Printer Driver DownloadDownload Printer Driver from Transact Web Sitewww.transact-tech.com1.First make sure your printer is powered on and connected to your PC. Then, download our Windows Vista driver for yourrespective printer model by going to our Service & Support section on our website at http://www.transact-tech.com/serviceand-support, then click on your printer model, and under “Drivers” download the Windows Driver for “Windows Server2003/2008, XP, Vista, 7, or 8 32-bit or 64-bit systems” at the top of the page.Note: If you are installing a Series 50, Series 70, Series 80/80PLUS, Series 90/90 PLUS, or a Series 150 printer,unfortunately we don’t have any Windows Vista drivers for these printers and don't plan on developing any since they areour older printers. Instead you want to Install a Generic/Text Only driver, which is included in Windows Vista, and willallow you to print. Please skip the steps below if you have a Series 50, Series 70, Series 80/80PLUS, Series 90/90PLUS orSeries 150 printer, and follow the instructions on the next page.2.Click on the Download link on the right hand side, and then click the Save button, and save the .zip file to your Desktop.3.On your Desktop you will then see the .zip file for the driver for your respective printer model. Double click this file, andunzip and extract the driver, then proceed with the following instructions to install the driver.

Printer Driver Installation on Vista (Add Printer) Click on StartSelect Control PanelSelect PrinterClick the Add a Printer buttonSelect Add a local printer, then click Next.

Printer Driver Installation on Vista (Add Printer) Select Use an existing port and select your portfrom the drop down menu, and then click Next. Ifyou have a Parallel Printer select LPT1, if you havea Serial Printer select COM1, and if you have aUSB Printer select the proper USB port. Note: In most cases if you have a USB printer, youwant to select USB001 as your port as this will bethe only USB port listed. If you have multiple USBports to choose from (USB002, USB003, etc.), runour USBPortView.exe utility, which can be found inthe Utilities folder of our Windows driver. After yourun the utility, look for the USB port that has“Transact” listed for the Manufacturer. So, forexample, if USB003 has “Transact” listed as theManufacturer, that is the port you will need tochoose in the Add Printer Wizard Note: If installing an Ethernet Printer, select“Create a new port”, then select Standard TCP/IPport for “Type of port”. You will need the IP addressto add the TCP/IP port.

Printer Driver Installation on Vista (Add Printer) Note: If you have a Series 50, Sereies 70,Series 80/80PLUS, Series 90/90PLUS, orSeries150 printer, select Generic for theManufacturer, and select Generic/TextOnly for the Printer, and then click Next.Then, skip the instructions below, and moveon to the next page. At the Select Manufacturer and PrinterWindow, click the Have Disk button, thenclick the Browse button, and go to thelocation where you extracted the driver to. Depending on what printer you are installingchoose the correct folder. For example, if you are installing an iTherm280/Epic 430/Epic 880/Ithaca 9000, openITherm-576 folder, and select theTactITherm-576.INF file. If you are installing a POSjet 1500/POSjet1000/BANKjet 1500/BANKjet 2500, selectthe IJet folder, then select the TactIJet.INFfile.

Printer Driver Installation on Vista (Add Printer) After you choose the proper .INF file, click theOpen button, then click the OK button Note: If you have a Series 50, Series 70, Series80/80PLUS, Series 90/90PLUS, or Series 150printer, move on to the next page.

Printer Driver Installation on Vista (Add Printer) You will now see your printer listed under a list ofavailable Ithaca printers to select. Select yourprinter, and then click the Next button. Note: If you have a POSjet 1500/POSjet1000/BANKjet 1500 printer, select SE1500 for yourprinter. Note: If you have a Series 50, Series 70, Series80/80PLUS, Series 90/90PLUS, or Series 150printer, move on to the next page.

Printer Driver Installation on Vista (Add Printer) If this screen comes up, select “Replace the currentdriver”, then click Next.

Printer Driver Installation on Vista (Add Printer) For the Printer name, leave it as it is, or name itwhatever you like, then select whether you want itas the default printer or not, then click Next.

Printer Driver Installation on Vista (Add Printer) Click the Finish button Note: Do not click the “Print a test page” button.Skip this for now.

Printer Driver Installation on Vista (Add Printer) After installing the printer, go to your Printer page,and right click on your printer and select PrinterProperties, then select the “Ports” tab, and uncheckthe “Enable bidirectional support” checkbox, andthen click Apply and then OK.Note: If this is checked, it can cause the printer toprint intermittently, or not print at all, and it ischecked by default after installing the printer, somake sure to uncheck it. Click on the General tab, and under the Generaltab, click the “Print Test Page” button to print aWindows Test Page, and the Windows Test Pageshould print out on your printer. Your printer is nowinstalled and ready to use.

Visual Quick Start GuidePrinter Driver Install on Windows Server 2003

Printer Driver DownloadDownload Printer Driver from Transact Web Sitewww.transact-tech.com1.First make sure your printer is powered on and connected to your PC. Then, download our Windows Server 2003 driver foryour respective printer model by going to our Service & Support section on our website at http://www.transacttech.com/service-and-support, then click on your printer model, and under “Drivers” download the Windows Driver for“Windows Server 2003/2008, XP, Vista, 7, or 8 32-bit or 64-bit systems” at the top of the page.Note: If you are installing a Series 50, Series 70, Series 80/80PLUS, Series 90/90 PLUS, or a Series 150 printer,unfortunately we don’t have any Windows Server 2003 drivers for these printers and don't plan on developing any since theyare our older printers. Instead you want to Install a Generic/Text Only driver, which is included in Windows Server 2003,and will allow you to print. Please skip the steps below if you have a Series 50, Series 70, Series 80/80PLUS, Series90/90PLUS or Series 150 printer, and follow the instructions on the next page.2.Click on the Download link on the right hand side, and then click the Save button, and save the .zip file to your Desktop.3.On your Desktop you will then see the .zip file for the driver for your respective printer model. Double click this file, andunzip and extract the driver, then proceed with the following instructions to install the driver.

Printer Driver Installation on Windows Server2003 (Add Printer) Click on StartSelect Control PanelSelect Printers and FaxesClick Add PrinterThe Welcome to the Add Printer Wizard windowshould come up (shown to the right). Click Next

Printer Driver Installation on Windows Server2003 (Add Printer) Select Local printer attached to thiscomputer. Also, make sure theAutomatically detect and install myPlug and Play printer checkbox isunchecked. Then click Next.

Printer Driver Installation on Windows Server2003 (Add Printer) Select Use the following port and select your portfrom the drop down menu, and then click Next. Ifyou have a Parallel Printer select LPT1, if you havea Serial Printer select COM1, and if you have aUSB Printer select the proper USB port. Note: In most cases if you have a USB printer, youwant to select USB001 as your port as this will bethe only USB port listed. If you have multiple USBports to choose from (USB002, USB003, etc.), runour USBPortView.exe utility, which can be found inthe Utilities folder of our Windows driver. After yourun the utility, look for the USB port that has“Transact” listed for the Manufacturer. So, forexample, if USB003 has “Transact” listed as theManufacturer, that is the port you will need tochoose in the Add Printer Wizard Note: If installing an Ethernet Printer, select“Create a new port”, then select Standard TCP/IPport for “Type of port”. You will need the IP addressto add the TCP/IP port.

Printer Driver Installation on Windows Server2003 (Add Printer) Note: If you have a Series 50, Sereies 70,Series 80/80PLUS, Series 90/90PLUS, orSeries150 printer, select Generic for theManufacturer, and select Generic/TextOnly for the Printer, and then click Next.Then, skip the instructions below, and moveon to the next page. At the Select Manufacturer and PrinterWindow, click the Have Disk button, thenclick the Browse button, and go to thelocation where you extracted the driver to. Depending on what printer you are installingchoose the correct folder. For example, if you are installing an iTherm280/Epic 430/Epic 880/Ithaca 9000, openITherm-576 folder, and select theTactITherm-576.INF file. If you are installing a POSjet 1500/POSjet1000/BANKjet 1500/BANKjet 2500, selectthe IJet folder, then select the TactIJet.INFfile.

Printer Driver Installation on Windows Server2003 (Add Printer) After you choose the proper .INF file, click theOpen button, then click the OK button Note: If you have a Series 50, Series 70, Series80/80PLUS, Series 90/90PLUS, or Series 150printer, move on to the next page.

Printer Driver Installation on Windows Server2003 (Add Printer) You will now see your printer listed under a list ofavailable Ithaca printers to select. Select yourprinter, and then click the Next button. Note: If you have a POSjet 1500/POSjet1000/BANKjet 1500 printer, select SE1500 for yourprinter. Note: If you have a Series 50, Series 70, Series80/80PLUS, Series 90/90PLUS, or Series 150printer, move on to the next page.

Printer Driver Installation on Windows Server2003 (Add Printer) If this screen comes up, select Replace existingdriver, then click Next.

Printer Driver Installation on Windows Server2003 (Add Printer) For the Printer name, leave it as it is, or name itwhatever you like, then select whether you want itas the default printer or not, then click Next.

Printer Driver Installation on Windows Server2003 (Add Printer) Select Do not share this printer, then click Next

Printer Driver Installation on Windows Server2003 (Add Printer) Select No when asked if you want to print atest page, then click Next.

Printer Driver Installation on Windows Server2003 (Add Printer) Click Finish to complete the installation

Printer Driver Installation on Windows Server2003 (Add Printer) After installing the printer, go to your Printers andFaxes page, and right click on your printer andselect Properties, then select the “Ports” tab, anduncheck the “Enable bidirectional support”checkbox, and then click Apply and then OK.Note: If this is checked, it can cause the printer toprint intermittently, or not print at all, and it ischecked by default after installing the printer, somake sure to uncheck it. Click on the General tab, and under the Generaltab, click the “Print Test Page” button to print aWindows Test Page, and the Windows Test Pageshould print out on your printer. Your printer is nowinstalled and ready to use.

Visual Quick Start GuidePrinter Driver Install on Windows XP

Printer Driver DownloadDownload Printer Driver from Transact Web Sitewww.transact-tech.com1.First make sure your printer is powered on and connected to your PC. Then, download our Windows XP driver for yourrespective printer model by going to our Service & Support section on our website at http://www.transact-tech.com/service-andsupport, then click on your printer model, and under “Drivers” download the Windows Driver for “Windows Server 2003/2008,XP, Vista, 7, or 8 32-bit or 64-bit systems” at the top of the page.Note: If you are installing a Series 50 or Series 70, unfortunately we don’t have any Windows XP drivers for these printers anddon't plan on developing any since they are our older printers. Instead you want to Install a Generic/Text Only driver, which isincluded in Windows XP, and will allow you to print. Please skip the steps below if you have a Series 50 or Series 70 printer,and foll

and-support, then click on your printer model, and under "Drivers" download the Windows Driver for "Windows Server 2003/2008, Windows XP, Windows Vista, Windows 7, Windows 8, Windows 8.1, and Windows 10 32-bit or . iTherm 280/Epic 430/Epic 880/Ithaca 9000, open ITherm-576 folder, and select the TactITherm-576.INF file. If you are .