mopdf.com

For Your Information .APPLICATIONNOTEIntegration of AuroRa Security withHoneywell Vista Series Security Control Panels#216OverviewThis application note details integration of the AuroRa Security package with Honeywell VistaSeries security panels. The goal of this document is to simplify the integration process and coverthe most common uses for the AuroRa Security package. This document assumes that the user isknowledgeable in the programming process for a Honeywell Vista Series Security Panel. Note thatwhile the intended focus of this application note is Honeywell security equipment, the basic principles of this process can be applied to any security system of similar architecture. When the processdescribed herein is complete, the Honeywell security system will successfully activate the AuroRaSecurity Lighting Scene upon the activating of appropriate security events.Goals of this Application Note1. Wire the Honeywell 4204 Relay Module to the AuroRa Security Interface.2. Configure the Honeywell Vista Panel to activate a contact closure using theStay Closed (Maintained) Action on the AuroRa Security Scene CCI.3. Configure the Honeywell Vista Panel to deactivate a contact closure on theAuroRa Security Scene CCI.Procedure1. Install and wire the Honeywell 4204 Relay Module to the AuroRa Security Interface.2. Program the Output Device Mappings.3. Program the Output Functions.Required Components 1 AuroRa Security Package (Lutron P/N AR-SECURITY-XX) 1 Honeywell Vista Series Security Panel (Honeywell P/N Vista-XXP) 1 Honeywell Alpha English Keypad (Honeywell P/N 6160) 1 Honeywell Relay Module (Honeywell P/N 4204)AuroRaSecurity PackageHoneywell Vista SeriesSecurity PanelHoneywell 4204Relay ModuleHoneywell 6160KeypadHoneywell Security Technical Support (800) 645-7492Lutron Technical Support Center (800) 523-9466

Sample ConfigurationThe sample floor plan below shows one possible configuration of the AuroRa Security LightingControl System. Note the security sensors installed in the home and their associated zone types.For example, the door sensor is a contact switch with an “Entry/Exit 1” zone type.This application note will demonstrate a procedure for activating the AuroRa Security Lighting Sceneusing the “Any Burglary Alarm” zone type on the Honeywell Vista Series Security Panel. Use of the“Any Burglary Alarm” zone type will allow activation of the Security Lighting Scene by all relevantsensors installed in the home.Contact SwitchPerimeter BurglaryContact SwitchPerimeter BurglaryContact SwitchEntry/Exit 1Dimmer 1Security Scene FlashUpDimmer 2Contact SwitchPerimeter BurglaryProximity SensorInterior FollowerDimmer 4Dimmer 3Dimmer 5Contact SwitchPerimeter BurglaryContact SwitchPerimeter BurglaryProgramming SummarySecurity Scene Activated by Zone Type (Any Burglary Alarm), Action Stay Closed Deactivated by Zone Type (Disarming), Action OffHoneywell Security Technical Support (800) 645-7492Lutron Technical Support Center (800) 523-9466

Install the Honeywell 4204 Relay ModuleIn this step, the 4204 Relay Module will be wired to the Honeywell Vista Series Security Panel.In addition, the 4204 Relay Module will be addressed and wired to the AuroRa Security Interface.1. Power down the security panel.2. Remove the cover from the 4204 Relay Module.3. Disable the Cover Tamper Switch at position 1 on the 4204 Relay Module DIP Switch (1 OFF).Note: If you want to enable cover tamper protection on the 4204 Relay Module, please reference Honeywell Security Documentation upon completion of this application note.4. Configure the DIP Switches to address the Relay Module.Select address 12 on the DIP Switches (2 ON, 3 ON, 4 OFF, 5 OFF).5. Wire the Relay Module to the panel communication bus as described in the included 4204 RelayModule directions. Note that the 4204 Relay Module shares this bus with other devices such asthe system keypad and optional devices such as the RF receiver.6. Wire pin 1 of the Honeywell 4204 Relay Module (Normally Open) to pin 1 of the AuroRa SecurityInterface connector (Security CCI).7. Wire pin 3 of the Honeywell 4204 Relay Module (Common) to pin 4 of the AuroRa SecurityInterface connector (Common).8. Power up the security panel.The 4204 Relay Module has been successfully wired and addressed.12411RELAY10RELAY9Honeywell 4204 Relay Module2RELAY34251On4-PinKeypad Plug67DIP SwitchCommonCCI 2CCI 1Security83Data OutGroundData In13141516RELAY11234NO NC CMN12 V5CoverTamperSwitch4 3 2 1AuroRaSecurityInterfaceTo PanelOn12345Honeywell Security Technical Support (800) 645-7492Lutron Technical Support Center (800) 523-9466

Program the Output Device MappingsIn this section, the Honeywell Vista Series Security Panel will be made aware of the 4204 RelayModule and Relay Number 1 will be mapped to Output Number 1.1. Enter the 4-digit Installer Code ( ) 800 onthe 6160 YPASS7 INSTANT8CODE9CHIME*0POLICEPAGEREADY#2. At the INSTALLER CODE prompt, press the * READY keyto continue.3. At the FIELD? prompt, enter 79 to enter Menu Mode:Output Device Mapping.4. At the ENTER OUTPUT NO. prompt, enter 01.Press the * READY key to continue.5. At the 01 OUTPUT TYPE prompt, enter 1. RELAY should appearunderneath the prompt. Press the * READY key to continue.Note: Vista-10P users will not see this prompt6. At the 01 MODULE ADDRESS prompt, enter 12 (the 4204 RelayModule address). Press the * READY key to continue.7. At the 01 RELAY POSITION prompt, enter 1 for relay number 1on the 4204 Relay Module. Press the * READY key to continue.8. At the ENTER OUTPUT NO. prompt, enter 00 to quit OutputDevice Mapping Programming.9. At the ENTER * OR # prompt, press the * READY key to continue.10. At the FIELD? prompt, press 99 to exit programming mode.Relay Number 1 has been successfully mapped to Output Number 1.Honeywell Security Technical Support (800) 645-7492Lutron Technical Support Center (800) 523-9466

Program the Output FunctionsIn this section, the Honeywell Vista Series Security Panel will be programmed to close OutputNumber 1 upon the activating of “Any Burglary Alarm.” In addition, the panel will be programmed toopen Output Number 1 upon Disarming of the alarm.1. Enter the 4-digit Installer Code ( ) 800 onthe 6160 YPASS7 INSTANT8CODE9CHIME*0POLICEPAGEREADY#2. At the INSTALLER CODE prompt, press the * READY keyto continue.3. At the FIELD? prompt, enter 80 to enter Menu Mode:Defining Output Functions.4. At the OUTPUT FUNCTION # prompt, enter 01.Press the * READY key to continue.5. The “Output Function Summary” screen should be displayed.Press the * READY key to continue.6. At the 01 ACTIVATED BY: prompt, enter 2 (Zone Type).Press the * READY key to continue.7. At the 01 ENTER ZONE TYPE prompt, enter 33 (Any Burglary Alarm).Press the * READY key to continue.8. At the 01 PARTITION prompt, enter 1 (Partition 1).Press the * READY key to continue.9. At the 01 OUTPUT ACTION prompt, enter 2 (Stay Closed).Press the * READY key to continue.10. At the ENTER OUTPUT NO. prompt, enter 01 (Output Number 01).Press the * READY key to continue.Honeywell Security Technical Support (800) 645-7492Lutron Technical Support Center (800) 523-9466

11. The “Output Function Summary” screen should be displayed.Press the * READY key to continue.12. At the OUTPUT FUNCTION # prompt, enter 02.Press the * READY key to continue.13. The “Output Function Summary” screen should be displayed.Press the * READY key to continue.14. At the 02 ACTIVATED BY: prompt, enter 2 (Zone Type).Press the * READY key to continue.15. At the 02 ENTER ZONE TYPE prompt, enter 22 (Disarming).Press the * READY key to continue.16. At the 02 PARTITION prompt, enter 1 (Partition 1).Press the * READY key to continue.17. At the 02 OUTPUT ACTION prompt, enter 0 (Off).Press the * READY key to continue.18. At the ENTER OUTPUT NO. prompt, enter 01 (Output Number 01).Press the * READY key to continue.19. The “Output Function Summary” screen should be displayed.Press the * READY key to continue.20. At the OUTPUT FUNCTION # prompt, enter 00 to exit.21. At the ENTER * or # prompt, press the * READY key to continue.22. At the FIELD? prompt, enter 99 to exit programming mode.The output functions have been successfully programmed.Congratulations! The Honeywell Vista Series Security Panel has been successfully set up to activatethe AuroRa Security Lighting Control System via the 4204 Relay Module. The Security Lighting Scenewill now be activated by the panel when “any burglary alarm” is activated. The lighting scene will bedeactivated when the panel is disarmed following the alarm.Honeywell Security Technical Support (800) 645-7492Lutron Technical Support Center (800) 523-9466

Advanced Security System ProgrammingThe Honeywell Vista Series Security Panel is capable of a wide range of additional programmingoptions. The sample floor plan from the Sample Configuration section of this application note isshown below. It has been amended to include the Zone Number to which each sensor is connected. This information can be used to develop output functions that trigger the Honeywell Security Systembased on Zone Lists or a specific Zone Number. An Advanced Programming configuration exampleis shown below. See the Vista Series manual for additional configuration possibilities.Optional Equipment Honeywell RF ReceiverHoneywell RF Transmitter (Key fob)Contact SwitchZone 2Perimeter BurglaryContact SwitchZone 2Perimeter BurglaryContact SwitchZone 1Entry/Exit 1Dimmer 1Security Scene FlashUpDimmer 2Contact SwitchZone 2Perimeter BurglaryProximity SensorZone 4Interior FollowerFire AlarmZone 3Supervised FireDimmer 4Dimmer 3Dimmer 5Flood SensorZone 324-Hour Audible AlarmContact SwitchZone 2Perimeter BurglaryFlood SensorZone 324-Hour Audible AlarmContact SwitchZone 2Perimeter BurglaryAdvanced Programming Summary:For help in developing advanced programming models such as Zone Lists and Zone Numbers,see your Vista Series Panel manual or call Honeywell Security Technical Support at (800) 645-7492.Security Scene Activated by Zone List (Zones 1, 2 and 4), Event Alarm, Action Stay Closed Deactivated by Zone Type (Disarming), Action OffCCI Scene 1 (Maintained) Activated by Zone Type (24-Hour Audible Alarm—Honeywell Zone Type 07),Event Alarm/Fault/Trouble, Action Stay Closed Deactivated by Zone Type (Disarming—Honeywell Zone Type 22), Action OffCCI Scene 1 (Momentary) Activated by Zone Number (Key fob ON Button), Event Fault, Action Close 2 SecondsCCI Scene 2 Activated by Zone Number (Key fob OFF Button), Event Fault, Action Close 2 SecondsHoneywell Security Technical Support (800) 645-7492Lutron Technical Support Center (800) 523-9466