Transcription

Pivot andPivot SetsArchitectural Solutions forDurable and EfficientHanging of Doors

PIVOTS AND PIVOT SETSTABLE OF CONTENTSGeneral Information. 4How to Select Product. 5Options. 6Certifications. 6Limited Warranty. 6Specifications. 6Product DescriptionsOffset Pivot Sets117-1/4Light-Duty/Light Weight Jamb Attached Pivot Set.7117Light-Duty/Light Weight Pivot Set.7173Very Light Duty/Weight Pivot Set.8147Standard-Duty Pivot Set.8L147Heavy Weight Pivot Set.9547Pivot Set for Arch Top or Overhead Concealed Closers .10165Pivot Set Without Bottom Pivot.10195Jamb Attached Pivot Set.11117-1/2Heavy Weight Pivot Set.12L117Heavy Weight/High Traffic/Lead Lined Door Pivot Set.13Offset Top Pivots180Standard Top Pivot.14180 x 102Top Pivot for Deep Reveal.14H180Heavy-Duty Top Pivot.14L180Heavy Weight/High Traffic/Lead Lined Door Top Pivot.15FA180Asylum Top Pivot.15280Half Surface Top Pivot.16380Half Mortise Top Pivot.16L380Half Mortise Heavy Weight/High Traffic/Lead Lined Door Pivot.16480Full Surface Top Pivot.17680Side Jamb Attached Top Pivot.17Intermediate Pivots119Light-Duty Pivot.18M19Standard-Duty Pivot.18M190Load-Bearing Pivot.18ML19Heavy Weight/High Traffic Pivot.19FA19Asylum Intermediate Pivot.19219Half Surface Pivot.20319Half Mortise Pivot.20L319Half Mortise Heavy Weight/High Traffic Pivot.20419Full Surface Pivot.20Electrified Intermediate PivotsE-M192Power Transfer Pivot.21Copyright 2014, Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

PIVOTS AND PIVOT SETSTABLE OF CONTENTS CONTINUEDElectrified Intermediate PivotsE-M19UPower Transfer High Inrush Pivot.21E-ML19Power Transfer Heavy Weight/High Traffic Pivot.22Electrified Intermediate Pivots (Cont'd)CS-M19Monitor Pivot.22CS-E-M19Monitor and Power Transfer Pivot.23CS-ML19Monitor Pivot Heavy Weight/High Traffic Pivot.23Electrified Intermediate Pivots - 1-1/2" OffsetE-M19Power Transfer Pivot.21CS-M19Monitor Pivot.22CS-E-M19Monitor and Power Transfer Pivot.23Pocket PivotsF519Pocket Pivot.24Electrified Pocket PivotE-F519Power Transfer Pocket Pivot.24Center Hung Pivot Sets127-3/4Light-Duty/Light Weight Jamb Attached Pivot Set.25128-3/4Light-Duty/Light Weight Pivot Set.25370Pivot Set.26117-3/4Heavy Weight Pivot Set.26H117-3/4Heavy Weight/High Traffic 2" Minimum Door Thickness.27H117-3/4 x 587Heavy Weight/High Traffic 1-3/4" Dr Moved Pivot Point.27176Very Light Duty/Weight Pivot Set.28178Pivot Set With Patch Fittings.28Center Hung Top Pivots320Light Weight/Light-Duty Top Pivot. 29340Top Pivot.29H340Heavy-Duty Top Pivot.29345Longer Throw Pin for Taller Doors Top Pivot.30H345Longer Throw Pin Heavy Weight/High Traffic for Taller Doors Top Pivot.30340 x 102Inverted Top Pivot.31340 x AP3Side Jamb Attached Top Pivot.31320 x 102Light-Duty Inverted Top Pivot.31Electrified Center Hung Top PivotsE-H340Power Transfer Pivot.32E-H345Power Transfer Longer Throw Pivot.32CS-340Monitor Pivot.33CS-345Monitor Pivot Longer Throw Pivot.33Quick Reference of Options. 34How to Order. 34Parts Drawings. 35-45Copyright 2014, Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.3

PIVOTS AND PIVOT SETSGENERAL INFORMATIONPivot sets provide the best possible means of hanging a door.They are designed to work with the laws of physics to providelong-lasting performance and reliability. The weight of the door is supported at the bottom by the floor- Uses principles of gravity to its advantageNeedle bearingsor bushing- Door swings with less resistance- Heavier doors can be accommodated Reduced stress on frame- Fasteners are in shear, not tension- Eliminates door sag- Vertically adjustable Heavy-duty hardened steel spindles- Thrust bearing supports vertical load- Needle bearings and bushings for lateral force- Extra heavy-duty models also have an additional surfaceapplied thrust bearing to handle heavier or high-trafficdoorsBottom arm Offset pivots provide better weight distribution and canaccommodate taller doorsHardened steelspindles Intermediate pivots are used for alignment and to ensureproper installation of bottom pivot or floor closer Center hung pivots are used for aesthetics or if the pivotpoint is going to be moved nearer the lock edge of the door PIVOTS DO NOT RETURN DOORS TO CENTER. Pivotsin this section are for door hanging means only. For doorcontrol see door closer catalog sections.Thrust bearing147 Pivot set and M19Intermediate pivot shown(recommended)4Copyright 2014, Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

PIVOTS AND PIVOT SETSHOW TO SELECT PRODUCT1. Offset vs. Center Hung Application3/4" Offset1-1/2"OffsetCenter HungPivot point located 3/4" from the heeledge of the door and 3/4" from faceof doorPivot point located 3/4" from the heel edge ofthe door and 1-1/2" from face of door. Extendedoffsets should be used when there is cladding onthe face of door or trim on the framePivot point centered in thicknessof door.2. Size of Door (width, height, thickness)Estimated door weights pounds per square foot (PSF)Door MaterialHollow MetalSolid Core WoodAluminum/Glass StorefrontBullet ResistentMDFTempered GlassLead Lining(add to door weight)3/4" Cladding(add to door weight)1-3/4"6.573.52073/8"51/16"5Wood3Example: 3/6 X 8/0 X 1/2" Tempered Glass DoorDoor: 28sq ft x 7lb./sq ft 196lbsFor doors of other sizes, consult factoryLarge department store entranceLarge office building entranceTheater entranceSchool entranceSchool restroom doorStore or bank entranceOffice building restroom mple: 3/0 X 7/0 X 1-3/4" WD X 1/4" Lead liningDoor: 21sq ft x 7lb./sq ft 147lbsLead Lining: 9.75 204.75lbsTotal Door weight: 351.75lbs2. Size of Door (width, height, thickness)ApplicationDoor Thickness2-1/4"794219Glass Thickness1/2"7Lead Thickness1/8"8Cladding MaterialStone10.5Daily CyclesYearly 0,000365,000225,000225,000150,000118,000School corridor doorOffice building corridor doorStore restroom doorResidential entrance door80756040Residential restroom doorResidential hallway doorResidential closet ,6002,200Copyright 2014, Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.Low5

PIVOTS AND PIVOT SETSOPTIONSFire Rated – Prefix FPivots for fire rated doors (up to 3 hours) include a steel top pivotand must have additional steel intermediate pivots. For F519pocket pivot, door assemblies must have been tested with pocketpivots.Twenty-minute label – Suffix - 20This UL rating is for 20-minute assemblies. Product with this ratinghas an authorized label.Less Top Pivot – Suffix LTPFor conditions requiring special top pivots or for arch top doors,the pivot set should be ordered less top pivot – LTP. For offsetinstallations, an additional load bearing intermediate (side jamb)M190 pivot is required. All intermediate pivots for that openingshould be M190's, not M19's.HandingAll offset pivots and pivot sets are handed. Suffix RH or LH.Special Layouts – Suffix SPLO#Unique installations or specially engineered products are calledspecial layouts. These numbers must be assigned by the technicalsupport department and they must be called out specifically by theirnumber when ordering.Extended Spindle – Suffix extra length neededAny special coverings or severe door undercuts will affectthe spindle height. In these applications, an extended spindlemay be required. Most standard spindle heights accommodatedoor undercuts up to 1/2". Extended spindles available in 1/2"increments up to 2" longer than standard. See template.Door Thickness – Suffix 1-3/4", 2", 2-1/4", 2-1/2" or 3"When ordering L series pivot for lead-lined doors, the thicknessof the door must be given. The purpose of the L product is tohave screws spaced so they straddle the lead in the center of thedoor. Also used when lead lining is under the skins of the door.Recommended for use on extra heavy or high traffic doors.1-1/2" Offset – Suffix 1-1/2Offset is the distance from the face of the door to the pivot point.Extended offsets should not be used unless there is cladding on theface of the door or there is trim to clear on the frame. 1-1/2" offsetarms and pivots are for doors with cladding or trim that project3/4" from the face of the door. The greater the offset the lessweight can be carried by the pivot.ElectroLynx Connectors – Suffix QC – Number of WiresThe plug-in connectors, with easy color coded wire system,eliminate matching wires. Must be used with ASSA ABLOY doors,frames and hardware. Available 4, 6, 8 or 12 wires for mostproducts.certificationsAll Rixson pivots and pivot sets are in compliance with ANSI/BHMA A156.4 Standards. See individual products for sub sections.limited warrantyRixson pivot sets are warranted for 2 years for defect. See Rixson Price Book for specific details of the limited warranty.specificationSAll pivots and pivot sets shall be of one manufacturer. All heavy-duty pivots shall have a minimum of 2 bearings internal to the bottompivot. One shall be a thrust bearing and the other a needle bearing. Separate bearing surfaces shall be in the top pivot. Lead-lined doorunits and high traffic pivots shall have additional thrust bearing. Fire rated pivot sets shall have steel top pivots. Fire rated doors requiresteel intermediate pivots.6Copyright 2014, Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

PIVOTS AND PIVOT SETSOFFSET HUNGModel 117-1/4Application Interior Doors Weight to 250 lbs.* Door Width up to 3'6"(1067mm) HandedANSI /C07172*D oor size & weight guidelines aredetermined using the appropriatenumber of intermediate pivots 117-1/4Product Description & Features Standard top pivot 180 included 119 intermediate pivot recommended (orderseparately); see page 18 Bottom pivot mortised into side jamb Not available for fire-rated doors Non-ferrous base material Doors 60" (1524mm) to 90" (2286mm) inheight should use one intermediate pivot.Each additional 30" (762mm) of door heightwarrants another intermediate pivot 3/4" (19mm) offset (measured fromcenterline of pivot to face of door) Door edges must be beveled 1/8" in 2" Weight of door borne by floor Furnished with wood and machine screws Extended spindles available in 1/2" (13mm)increments up to 2" (51mm) longer thanstandardTechnical InformationProduct Description & Features Standard top pivot 180 included 119 intermediate pivot recommended (orderseparately); see page 18 Bottom pivot mortised into floor Available for fire door assemblies up tothree hours – specify F117. Intermediatepivot required by UL. Specify FM19, (orderseparately), see page 18 For 20-minute label suffix “–20” to the partnumber Non-ferrous base material Doors up to 90" (2286mm) in height shoulduse one intermediate pivot. Each additional30" (762mm) of door height warrants anotherintermediate pivot 3/4" (19mm) offset (measured from centerline ofpivot to face of door) Available for 1-1/2" (38mm) offset (door weight150 lbs) for doors with cladding or framemolding. Door edges must be beveled 1/8" in 2" Furnished with wood and machine screws Extended spindles available in 1/2" (13mmincrements up to 2" (51mm) longer than standard Doors will swing 180 , trim permittingTechnical InformationFrame stop requiredModel 117Application Interior Doors Weight to 300 lbs.* Door Width up to 3'6"(1067mm) HandedANSI/C07162/C07202*D oor size & weight guidelines aredetermined using the appropriatenumber of intermediate pivots 117Frame stop requiredCopyright 2014, Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.7

PIVOTS AND PIVOT SETSOffset HungModel 173Application Product Description & FeaturesInterior DoorsWeight 150 lbsDoor Sizes up to 3'0" x 8'0" x 1-3/4"Handed Standard top pivot 180 includedTechnical Information117-1/4Frame stop required 119 intermediate pivot recommended for alldoors over 6'8" (order separately) see page18 Bottom pivot mounts directly to concrete floor Uses same arm and cap as 117 pivot set Non-ferrous base metal 3/4" offset only (measured from centerline ofpivot to face of door) Available for 1-1/2" (38mm) offset (doorweight 100 lbs) for doors with cladding orframe molding3/8"(10) Door edges must be beveled 1/8" in 2" Furnished with wood and metal screws 3/8" vertical adjustment No spindle extensions availableANSI/C07162/C07202 Door will swing 180 , trim permitting1-3/32"(28)1-3/4"(9)3/4"(13)Model 147Application Exterior or Interior DoorsWeight to 600 lbs.*Door Width up to 4'0" (1219mm)HandedANSI/C07162/C07202*D oor size & weight guidelines aredetermined using the appropriate numberof intermediate pivots 8Product Description & Features Standard top pivot 180 included M19 intermediate pivot required (orderseparately); see page 18 Bottom pivot mounts directly to floor Uses same arm and cap as 27 floor closer Available for fire door assemblies up tothree hours (ferrous material) – specify F147.Intermediate pivot required by UL. SpecifyFM19 (order separately), see page 18 For 20-minute label suffix “–20” to the partnumber Non-ferrous base material Doors 60" (1524mm) to 90" (2286mm) inheight should use one intermediate pivot.Each additional 30" (762mm) of door heightwarrants another intermediate pivot 3/4" (19mm) offset (measured from centerlineof pivot to face of door) Available for 1-1/2" (38mm) offset (doorweight 350 lbs.) for doors with cladding orframe molding Door edges must be beveled 1/8" in 2" Furnished with wood and machine screws Extended spindles available in 1/2" (13mm)increments up to 2" (51mm) longer thanstandard Doors will swing 180 , trim permittingCopyright 2014, Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.Technical Information147Frame stop required

PIVOTS AND PIVOT SETSOffset hungModel L147ApplicationProduct Description & FeaturesTechnical Information Exterior or Interior Doors Lead-Lined/Heavy/High Traffic Doors Weight to 800 lbs. Door Width up to 4'0" (1219mm)Handed Standard top pivot L180 includedFrame stop required ML19 intermediate pivot required (orderseparately), see page 19 Bottom pivot mounts directly to floor Doors with lead lining under the skin shouldalso use this product. Screw holes in top pivot and bottom armspaced to straddle lead lining in the middle ofthe door Available for fire door assemblies up to threehours for 1-3/4" (44mm) doors only (ferrousmaterial) – specify FL147. Intermediatepivot required by UL. Specify FML19 (orderseparately), see page 19 For 20-minute label suffix “–20” to the partnumber Non-ferrous base materialANSI/C07162/C07202 Doors 60" (1524mm) to 90" (2286mm) inheight should use one intermediate pivot.Each additional 30" (762mm) of door heightwarrants another intermediate pivot Available to accommodate lead in doorthicknesses 1-3/4" (44mm), 2" (51mm),2-1/4" (57mm), 2-1/2" (64mm), or 3" (76mm)– specify when ordering1-3/4" door shown 3/4" (19mm) offset (measured from centerlineof pivot to face of door) Door edges must be beveled 1/8" in 2" Furnished with wood and machine screws Extended spindles available in 1/2" (13mm)increments up to 2" (51mm) longer thanstandard Doors will swing 180 , trim permittingCopyright 2014, Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.9

PIVOTS AND PIVOT SETSOFFSET HUNGMODEL 547Application Exterior or Interior DoorsFor Arch Top Doors or OverheadConcealed ClosersWeight to 500 lbs.Door Width up to 3'6" (1067mm)HandedProduct Description & FeaturesTechnical Information Set consists of two each M190 intermediatepivots and bottom pivotFrame stop required547 Bottom pivot mounts directly to floor5/16(8) Available for fire door assemblies up to threehours. Specify F547. Intermediate pivotsFM190 included3/4(19) For 20-minute label suffix “–20” to the partnumber5(127) Non-ferrous base material5(127)4-1/4(108) Doors 60" (1524) to 90" (2286mm) in heighthave two intermediate pivots. Each additional30" (762mm) of door height warrants anotherintermediate pivot5(127) 3/4" (19mm) offset (measured from centerlineof pivot to face of door)5(127)4-1/4(108)13/16(21) Door edges must be beveled 1/8" in 2" Furnished with wood and machine screwsANSI/C07162 (modified)/C072022-13/16(71) Extended spindles available in 1/2" (13mm)increments up to 2" (51mm) longer thanstandard2-13/16(71)3/4(19)5/16(8)1"(25)3/16(5) Doors will swing 180 , trim permittingMODEL 165ApplicationProduct Description & Features Exterior or Interior Doors For Doors Without Bottom Pivots Weight to 300 lbs. Door Width up to 3'6" (1067mm) Handed Set consists of one H180 top pivot andtwo each M190 intermediate pivotsTechnical Information165Frame stop required Not available for fire door assemblies4-1/4(108) Non-ferrous base material D oors 60" (1524mm) to 90" (2286mm) inheight have two intermediate pivots. Eachadditional 30" (762mm) of door heightwarrants another intermediate pivot3/4(19)1/4(6)1/4(6) Door edges must be beveled 1/8" in 2"5/16(8) Furnished with wood and machine screws Doors will swing 180 , trim permitting3/4(19)5(127)10Copyright 2014, Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.3/4(19)13/16(21) 3/4" (19mm) offset (measured from centerlineof pivot to face of door)ANSI/C07162 (modified)1-1/16(27)5(127)4-1/4(108)

PIVOTS AND PIVOT SETSOFFSET HUNGMODEL 195Application Exterior or Interior Doors Weight to 450 lbs.* Door Width up to 4'0" (1219mm)Handed195Product Description & FeaturesTechnical Information Standard top pivot 180 includedFrame stop required 119 or M19 intermediate pivots arerecommended (order separately), see page18 Bottom pivot mortised into side jamb Pivot set can be vertically adjusted up to3/16" (5mm) after installation without the useof shims Doors 60" (1524mm) to 90" (2286mm) inheight should use one intermediate pivot.Each additional 30" (762mm) of door heightwarrants another intermediate pivot Non-ferrous base material Available for fire door assemblies up tothree hours. Specify F195. Intermediatepivot required by UL. Specify FM19 (orderseparately), see page 18ANSI/C07131 3/4" (19mm) offset (measured from centerlineof pivot to face of door) Door edges must be beveled 1/8" in 2" Weight of door is borne by floor portion*D oor size & weight guidelines aredetermined using the appropriatenumber of intermediate pivots Furnished with wood and machine screws Extended spindles available in 1/2" (13mm)increments up to 2" (51mm) longer thanstandard Doors will swing 180 , trim permittingCopyright 2014, Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.11

PIVOTS AND PIVOT SETSOFFSET HUNGModel 117-1/2Application Exterior or Interior DoorsWeight to 650 lbs.*Door Width up to 4'0" (1219mm)HandedProduct Description & FeaturesTechnical Information Standard top pivot 180 includedFrame stop required M19 intermediate pivot required (order separately),see page 18 Bottom pivot mortised into floor Available for fire door assemblies up to threehours (ferrous material) – specify F117-1/2.Intermediate pivot required by UL. SpecifyFM19 (order separately), see page 18 For 20-minute label suffix “–20” to the partnumber Non-ferrous base material Doors 60" (1524mm) to 90" (2286mm) inheight should use one intermediate pivot.Each additional 30" (762mm) of door heightwarrants another intermediate pivot 3/4" (19mm) offset (measured from centerlineof pivot to face of door)ANSI/C07121/C07202 Available for 1-1/2" (38mm) offset (doorweight 350 lbs.) for doors with cladding orframe molding Door edges must be beveled 1/8" in 2"*D oor size & weight guidelines aredetermined using the appropriatenumber of intermediate pivots Furnished with wood and machine screws Extended spindles available in 1/2" (13mm)increments up to 2" (51mm) longer thanstandard Doors will swing 180 , trim permitting12Copyright 2014, Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.117-1/2

PIVOTS AND PIVOT SETSOFFSET HUNGMODEL L117ApplicationProduct Description & FeaturesTechnical Information Exterior or Interior Doors Lead-Lined/Heavy/High TrafficDoors Weight to 1,750 lbs.* Door Width up to 4'0"(1219mm) Handed Standard top pivot L180 includedFrame stop required ML19 intermediate pivot required (orderseparately), see page 19 Bottom pivot mortised into floor Available for fire door assemblies up to three hours(ferrous material). Specify FL117. Intermediate pivotrequired by UL. Specify FML19 (order separately),see page 19. Note: UL listing for 1-3/4" thickdoors only Available to accommodate lead in doorthicknesses 1-3/4" (44mm), 2" (51mm),2-1/4" (57mm)

Rixson pivot sets are warranted for 2 years for defect. See Rixson Price Book for specific details of the limited warranty. All pivots and pivot sets shall be of one manufacturer. All heavy-duty pivots shall have a minimum of 2 bearings internal to the bottom pivot. One shall be a thrust bearing and the other a needle bearing.