
Transcription
SFP DSL ModuleMounting Instructions
SFP DSL Module Mounting InstructionsPlease noteÌ This SFP DSL module allows you to directly connect your appliance to a VDSL2 linewithout using a separate modemÌ It supports all VDSL2 standards defined in ITU –T G.993.2, G.994.1, G.997.1,and theVDSL2 profiles 8a, 8b, 8c, 8d, 12a, 12b, 17a , 30a.Ì The SFP DSL module is supported on all SG/XG/XGS appliances.Ì On SG/XG 105(w)/115(w) and XG 106(w) models the SFP port is shared with RJ45Ethernet Port E3/Port 4 and takes precedence. Hence this RJ45 port can no longerbe used when using the SFP DSL module.LED StatusDSL Status right LEDLeft LED1GreenAmberSlowly BlinkingIdleRapidly BlinkingTrainingConstantlyConnected to ISPVery Rapidly BlinkingPacket transmitConstantlyNormal operation
SFP DSL Module Mounting InstructionsMounting the SFP DSL module1.1. Insert the SFP DSL module into theSFP port of your appliance2. Connect the SFP DSL module to theDSL wall plug or splitter by using aphone cable (RJ11)3. The SFP DSL module is trying toconnect to the ISP (Status LED startsblinking - see LED status table)4. After the connection to the ISP hasbeen successfully established theStatus LED will turn into constantgreenSFP Port2.DSL wall plug/splitter3/4.Caution! During operationthe module could get very hot.Status LED (Green)2
SFP DSL Module Mounting InstructionsConfigure your DSL connection on your FirewallÌ Use your browser to connect to the WebAdmin GUI of your appliance.Ì On Firewalls running Sophos UTM: Go to the section 'Interfaces & Routing Interfaces' On 105/115 models edit the Interface eth3 (on 125/135 models edit theinterface eth8) and change the Type to 'DSL (PPPoE)'Ì On Firewalls running SFOS: Go to the section 'Network Interfaces' On 105/106/115 models edit Interface 4 (on 125/135 models edit Interface 9)and change IP assignment to 'DSL' On XGS models edit the SFP interface which you inserted the DSL module intoand change IP assignment to 'DSL'Ì Activate the DSL service you want to use and enter Username/PWÌ Please note: you might be required to enter a VLAN ID/tag provided by your ISP aswellÌ Save your changes3
SFP DSL-Modul Montage AnleitungBitte beachtenÌ Dieses SFP DSL-Modul ermöglicht eine direkte Verbindung Ihrer Appliance miteinem VDSL2- Anschluss ohne Nutzung eines separaten DSL-ModemsÌ Es unterstützt alle VDSL2 Standards definiert in ITU –T G.993.2, G.994.1,G.997.1,sowie die VDSL2 Profile 8a, 8b, 8c, 8d, 12a, 12b, 17a, 30a.Ì Das SFP DSL-Modul wird von allen SG/XG/XGS Modellen unterstützt.Ì Bei SG/XG 105(w)/115(w) sowie XG 106(w) wird der SFP-Port mit RJ45 EthernetPort E3/Port4 geteilt und hat Vorrang. Daher kann der RJ45-Port nicht mehrgenutzt werden sobald das SFP DSL-Modul eingesetzt wird.LED StatusDSL Status rechte LEDLinke LEDGrünGelbLangsam blinkendKonstantSchnell blinkendVerbindungsversuchKonstantMit ISP verbundenSehr schnell blinkendDatenübertragungKonstantNormalbetrieb4
SFP DSL-Modul Montage AnleitungEinsetzen des SFP DSL-Moduls1.2. Verbinden Sie das SFP DSL-Modulmit Ihrem DSL-Anschluss (Wanddoseoder Splitter) unter Verwendung einesStandard-Telefonkabels(RJ11)SFP Port1. Setzen sie das SFP DSL-Modul in denSFP-Port ihrer Appliance ein3. Das SFP DSL-Modul versucht nuneine Verbindung zum ISP aufzubauen(Status LED blinkt schnell - sieheLED Status-Tabelle)4. Nach erfolgreicher Verbindung mitdem ISP leuchtet die Status-LEDkonstant grünAchtung! Während desBetriebs kann das Modul sehrheiß werden.52.DSL Wanddose/Splitter3/4.Status LED (grün)
SFP DSL-Modul Montage AnleitungDSL-Verbindung auf der Firewall konfigurierenÌ Stellen Sie über den Browser eine Verbindung mit der WebAdminBenutzeroberfläche her.Ì Auf einer Firewall mit Sophos UTM Betriebssystem: Gehen Sie zur Section „Interfaces & Routing Interfaces“ Bei Modellen 105/115 editieren Sie Interface eth3 (bei Modellen 125/135Interface eth8) und ändern Sie den Type in „DSL (PPPoE)“Ì Auf einer Firewall mit SFOS Betriebssystem: Gehen Sie zur Section Network Interfaces Bei Modellen 105/106/115 editieren Sie Interface 4 (bei Modellen125/135 Interface 9) und ändern Sie IP assignment in „DSL“ Bei XGS-Modellen editieren Sie das SFP-Interface, in welches Sie dasDSL-Modul eingesetzt haben und ändern Sie IP assignment auf "DSL"Ì Aktivieren Sie den DSL-Service, den Sie nutzenwollen und geben Sie Username/PW einÌ Bitte beachten: Möglicherweise müssen Sie eine VLAN ID/tageingeben, die Ihnen vom ISP zur Verfügung gestellt wirdÌ Sichern Sie die Konfiguration6
SFP DSL Module Mounting InstructionsSales DACH(Deutschland, Österreich, Schweiz)Tel.: 49 (0) 611 585 8-0Tel.: 49 (0) 721 255 16-0E-Mail: [email protected] SalesTel: 65 62244168Email: [email protected] Kingdom and Worldwide SalesTel: 44 (0)8447 671131Email: [email protected] American SalesToll Free: 1-866-866-2802Email: [email protected] Copyright 2021. Sophos Ltd. All rights reserved.Registered in England and Wales No. 2096520,The Pentagon, Abingdon Science Park, Abingdon, OX14 3YP, UKSophos is the registered trademark of Sophos Ltd. All other product and companynames mentioned are trademarks or registered trademarks of their respective owners.21-02-11 (DD)Australia and New Zealand SalesTel: 61 2 9409 9100Email: [email protected]
SFP DSL Module Mounting Instructions Mounting the SFP DSL module 1. Insert the SFP DSL module into the SFP port of your appliance 2. Connect the SFP DSL module to the DSL wall plug or splitter by using a phone cable (RJ11) 3. The SFP DSL module is trying to connect to the ISP (Status LED starts blinking - see LED status table) 4.