Transcription

TOSHIBA AMERICA INFORMATION SYSTEMSSTORAGE DEVICE DIVISIONIRVINE, CALIFORNIASD-M1612DVD-ROM DRIVEUSER MANUAL

CONTENTSIntroduction.1Setup .3Using the DVD-ROM Drive .6Troubleshooting.9Specifications .10Drive Connectors.13

INTRODUCTION – SD-M1612 DVD-ROM DriveGeneral FeaturesTray Loading Mechanism3-way Disc Eject (eject button, software, emergency eject hole)Average Random Access TimeCD-ROMDVDDVD-RAM85ms95ms170msDAE (Digital Audio Extraction) Audio CapabilityMPC3 CompatibilityMulti-Read CapabilityRegionalization (RPC2 compliance) (DVD)ATAPI BUS Interface:Drive SpeedDVDCDDVD-RAM16X Single Layer10X Dual Layer48X2X (ver 1.0)1X (ver 2.1)Types of Disc Formats SupportedDVD1 DVD-ROMDVD-5 - Single-sided/Single LayerDVD-9 - Single-sided/Dual LayerDVD-10 - Double-sided/Single LayerDVD-18 - Double-sided/Dual Layer DVD-R, DVD-RW, DVD-RAM (Read)

CD CD-DACD (E)GCD-MIDICD-TEXTCD-ROMCD-ROM-XACD-I Bridge (Photo-CD, Video CD)CD-IMulti-session (Photo-CD, CD Extra, CD-RW, CD-R)CD-R (Read)CD-RW (Read)Front PanelFigure 1.SD-M1612 DVD-ROM Drive Front PanelLoading TrayLoad disc using tray.Busy IndicatorWhen you install a disc into the DVD-ROM drive, the BUSY light flashes slowly as itattempts to locate the disc. One of the following will occur: BUSY light goes out. The DVD-ROM drive is ready to read data from the disc. BUSY light flashes slowly. The disc may be dirty. BUSY light remains ON. The DVD-ROM is accessing data. BUSY light remains ON indefinitely. The DVD-ROM is experiencing an errorEjectButtonThe Eject button is used to open the disc tray so you can install or remove a disc.EmergencyEject HoleThe emergency eject hole is to be used only when the Loading Tray will not open whenEject button is pressed.

SETUP – SD-M1612 DVD-ROMThe following steps must be performed to properly install your drive: Set Drive Jumper Settings Connect Audio Cable (optional) Attach IDE BUS Cable Attach Power Cable Mount DriveJumper SettingsThe mode select jumpers are 6 straight angle pins located on the rear of the DVD-ROM drive.By placing a jumper on the pins, you can select the following functions:CSSLMADrive is configured using host interface signal CSELConfigures drive as SlaveConfigures drive as Master (default mode)Figure 1.Mode Select JumperIn most installations, jumper should remain in the MA position (factory default). It is recommended thatyou install your DVD-ROM drive only on the secondary IDE BUS. If you are installing on primary IDEBUS, your hard drive would then be the Master, and you should set your DVD-ROM drive to the Slaveposition (SL)Figure 2.Jumper Locations3

Placing DVD-ROM Drive inside your ComputerNow that you have set the jumpers, you are ready to install your DVD-ROM drive inside your computer.Important Note: Disconnect power from your computer system before beginning installation.Remove computer cover and faceplate if required. Refer to your computer systems manual for removalinformation. If the DVD-ROM drive is replacing a CD-ROM or DVD-ROM, remove drive presentlyinstalled in your system.Your Toshiba DVD-ROM drive can be placed in any free half-height drive slot at the front of yourcomputer. (It can be mounted horizontally or vertically.)Carefully start sliding the DVD-ROM drive into the opening with the disc tray facing the front of thecomputer. Before you push the drive all the way in you will need to connect the IDE BUS cable, Audiocable and the Power cable on the back of the drive.Connecting CablesIDE BUS Cable (not supplied with drive) - Your computer system should have a primary and secondaryIDE BUS, cable with your Hard Drive most likely being the Master on the primary BUS. Connect BUScable as follows, assuring that pin 1 of cable (side with red stripe) is connected to pin 1 of the DVD-ROMdrive's interface connector:If you are replacing your CD-ROM or DVD:connect DVD-ROM drive to the BUS Cable connectorthat the CD-ROM or DVD was connected to.If DVD-ROM drive is not replacing a CD-ROM/DVD or isan addition to a CD-ROM/DVD:connect DVD-ROM drive to an open connector on thesecondary IDE BUS cable (not supplied with drive).If DVD-ROM drive is to be slave on Primary BUS:connect DVD-ROM drive to open connector on theprimary IDE BUS cable (not supplied with drive).Figure 3.Installing BUS CablePower Cable - Connect an internal computer powersupply cable to the power socket at the back of theDVD-ROM drive. One side of the plug has chamferededges, so the power connector fits only one way. Pushplug completely into the socket making sure the plug fitscorrectly.Figure 4.Installing Power Cable4

Audio Cable (optional) - If you have a sound card andspeakers, and would like to play audio CDs on yourcomputer, you will need to install a CD/DVD audio cable.Toshiba's DVD-ROM drives use a standard 4-pin audiocable that can be purchased from most local computersuppliers. The sound cable connects to your sound cardat one end and the other end connects to the digitalaudio connector at the left rear of the DVD-ROM drive(see DVD-ROM drive Back Panel photo for location).Refer to the instructions that came with your sound cardfor details on any sound-driver software required.Figure 5.Installing Audio CableCompleting InstallationAfter you have connected all the necessary cables,push the DVD-ROM drive completely into thecomputers drive slot. Mount drive per your computersinstructions. The screw length should not exceed30.5mm (measured from outside surface of side orbottom of drive to tip of screw). Replace computercover and all outer screws.Figure 6.Mounting IllustrationSoftware Driver - Toshiba's optical drives do not require any unique device drivers for Windows'95/'98/2000/Me/XP/NT. After installing your drive and re-booting, your system should recognize yourdrive. Windows '95/'98/2000/Me/XP/NT Operating Systems support all Toshiba optical drives natively Ifyou prefer using DOS, download the DOS ATAPI driver from our web site.5

USING THE DVD DVD-ROM Drive – SD-M1612Drive OperationInserting a Disc - HorizontallyTo insert a disc into a drive that is mounted horizontally, perform the following steps:Figure 1.Inserting Disc1. Open the drive's Loading tray by pressing the Eject Button.2. Place disc into drive's Loading tray3. Press Eject button again or gently push on the open disc tray. Tray will automatically close.Inserting a Disc - VerticallyTo insert a disc in a drive that is mounted vertically, perform the following steps:1. Locate sliding disc holders (4 locations) on drive's Loading Tray.2. Position the disc behind the disc holders3. Close the drive by gently pushing in the tray or pressing the eject button.Figure 2.Inserting Disc Vertically6

Removing a DiscTo remove a disc from the DVD-ROM drive, perform the following steps:1. Open the Loading Tray by pressing the Eject Button.2. Grasp disc by edges, and lift out of loading tray.3. Press Eject Button again to close Loading Tray.Usage Guidelines Keep the disc tray closed when not using the DVD-ROM Drive.Do not press down on the disc tray when opening or closing it.Do not place objects on the disc tray.Never use a damaged, broken, or deformed disc.Do not press the Open/Close button while the drive is playing a DVD movie or accessing a disc.To stop a DVD movie, click Stop button in the DVD player application program.NOTE: High-speed drives spin the disc at a high rotational speed. If a disc has printing on only half of thedisc, or if there is a slight imbalance in the disc, the imbalance is greatly magnified by the high speed,causing the drive to vibrate or produce a fan-like noise. These effects are inherent in the high-speedtechnology and do not indicate a problem with the drive.Emergency EjectionCAUTION: The following procedure is intended only as a last resort when pressing theeject button fails to open the Loading Tray1. Turn computer power OFF by properly shutting down system.2. Insert a solid bar (i.e. large paper clip) into Emergency Eject hole and push as shown in thepicture below3. DVD tray will open/eject.Figure 3.Using Emergency EjectThis procedure cannot be repeated without cycling the DVD-ROMs (computer's) power.After the media is removed and the loading tray is closed, the tray will not reopen without first turning thepower ON/OFF.7

NOTE: Use a bar that is less than 1.5 mm in diameter.Do not insert more than 50mm in depth.Inserting more than 50mm may damage the DVD-ROM drive.Handling MediaDVD media is sensitive to dust and fingerprints. Carefully handle media by its edges only. If a DVDmovie skips or hangs during playback, clean the media. Most DVD video playback issues are mediarelated and can be remedied by proper handling and care of media.Cleaning MediaTry to avoid touching the read area (underside) of the disc as dirt and smears will degrade the discaccessing speed.If the disc becomes dirty wipe it with a damp soft cloth. Avoid cleaning in a circular motion, but ratherfrom the inner side outward.8

TROUBLESHOOTING – SD-M1612SolutionProblemDisc tray cannot be opened Check that there is power to drive.Use Emergency Eject instructions to open tray.Drive is not recognized by system Is the drive connected properly? Are all cables plugged in properly (e.g.Power Cable, Interface Cable and Audio Cables).Are the drive configuration jumpers on the DVD-ROM drive setproperly?Is the software driver loaded? On a step-by-step (F8) Boot of thesystem is the DVD-ROM drive recognized?(BIOS / DOS reports "device driver not found" or "no valid driversselected.). If not, Contact Technical Support.Has the DVD-ROM drive software driver been corrupted by a virus. Runa Virus Scan program and repair if possible. Contact Technical Supportif the Virus renders the DVD-ROM drive software drivers not useable. Drive is not recognized by systemduring Boot process, but isrecognized by the OperatingSystem (i.e. XP, Win2000, Win98,Win NT, etc.) BUSY Indicator LED flashesslowly Is the DVD-ROM drive software driver loaded? On a step-by-step (F8)Boot of the system is the DVD-ROM drive recognized?(BIOS / DOS reports "device driver not found or no valid DVD driversselected.). If not, Contact Technical Support.Has the Windows DVD-ROM drive software driver program beencorrupted by a virus. Run a Virus Scan program and repair if possible.Contact Technical Support if the Virus renders the software drivers notuseable.The disc may be dirty Clean it with a soft damp cloth. Avoid cleaning thedisc using a circular motion. The disc should be wiped in a radialdirection. That is, from the inner side outward.The laser lens may have become cloudy or blocked by particulatematter. Please contact Technical Support.BUSY Indicator LED is constantlyON Possible Hardware Problem. Please contact Technical Support.DVD-ROM can not play a DVD inthe drive or certain types of CDmedia (i.e. CD-plus, etc.) Is the DVD-ROM drive driver loadedIs the DVD disc the correct format for the type of system that you areusing? (i.e. on a PC an ISO9660 IBM compatible PC format as opposedto Apple/Mac HFS disc or UNIX disc formats which will not function).Do you have the correct software applications program/drivers installedto run a DVD disc?Has the Windows DVD-ROM drive software driver program beencorrupted by a virus. Run a Virus Scan program and repair if possible.Contact Technical Support if the Virus renders the software drivers notuseable. 9

SPECIFICATIONS –SD-M1612GeneralInterfaceATAPICompatible DVD-ROM StandardsDVDDVD-ROM (DVD-5, DVD-9, DVD-10, DVD-18)DVD-R, DVD-RW, DVD-RAMCDCD-DACD-ROMCD-I Bridge (Photo-CD, Video CD)Multi-session (Photo-CD, CD Extra, CD-RW, CD-R)CD-MINICD-TEXTCD (E)GCD-ROM-XACD-ICD-R (Read)CD-RW (Read)Storage CapacitiesDVD4.377GB (DVD-5)7.959GB (DVD-9)8.754GB (DVD-10)15.917GB (DVD-18)3.679GB (DVD-R, Ver. 1.0)4.377GB (DVD-R, Ver. 2.0)2.324GB (DVD-RAM, Ver 1.0)4.377GB (DVD-RAM, Ver 2.1)CD656.5MB (mode 1)748.8MB (mode 2)10

PerformanceRotational SpeedDVD-ROM(6.0X - 16X) single layer(4.1X - 10X) dual layerDVD-R (Ver 2.0), DVD-RW(2 - 4.8X)DVD-R (Ver 1.0) (2 - 4.8X)DVD-RAM (Ver 1.0) (2X)DVD-RAM (Ver 2.1) (1X)DVD-Video CSS-disc (2 - 4.8X)CD-ROM, CD-R/RW(20.7 - 48X)CD-DA Transfer (14 - 32X)CD-DA/Video CD (4X - 7.8X)9,200rpm6,300rpm2,780rpm3,200rpm2,160 - 4,800rpm1,380 - 3,300rpm2,780rpm9,500rpm1,800 - 4,300rpm1,200 - 2,000rpmData Transfer RateDVD (Single)DVD (Dual)DVD-VideoDVD-R, DVD-RWDVD-RAM ( Ver 1.0)CD (mode 1)CD-(mode 2)Burst Rate8,910 - 21,600 KBytes/s5,540 - 13,500 KBytes/s2,704 – 6,536 KBytes/s2,704 – 6,536 KBytes/s2,704 KBytes/s3,105 – 7,200 KBytes/s3,105 – 7,200 KBytes/s16.7 Mbyte/s (PIO Mode 4)16.7 Mbyte/s (multiple word DMA transfer mode 2)33.3 MByte/s (Ultra DMA)Random Access TimeCDDVDDVD-RAMData Error RateDVDCD85ms95ms170ms10-15 Max10-15 Max (Mode 1)10-12 Max (Mode 2)Spin-up TimeDVDDVD-RAM (Ver 2.1)DVD-RAM (Ver 1.0)CD1.5s Typ1.5s Typ1.9s Typ1.4s TypData Buffer512Kbytes11

ReliabilityMTBFPower ON HoursON/OFF CyclesNumber of AccessOperating Duty CycleMTTR100,000 hours5,436 hours/year313 cycles/yea600,000 accesses/year20% of Power ON time (Reading/Seeking)0.5 hoursAudioNumber of Channels2Frequency Response20Hz to 20,000 HzDistortion-80 dB (at 1kHz JIS A-weighted)Output LevelsHeadphoneAnalog Line OutDigital Line Out0.90V (rms Typ)0.79 V (rms Typ)0.50 V (p-p)EnvironmentalAmbient TemperatureOperatingStorageShipping5 to 50 C (41 to 122 F)-10 to 60 C (-14 to 140 F)-40 to 65 C (-40 to 149 F)Temperature GradientOperatingStorage/Shipping11 C/hour (max)20 C/hour (max)Relative HumidityOperatingStorage/Shipping8% to 85%5% to 95% (wet bulb 27 C max)VibrationOperatingNon-operatingno hard error: 10 to 500 Hz 2.45 m/s2 [0.25G] (O-P)(excludes resonance point)no damage: 5 - 10Hz 5mm (P-P)10 - 500Hz 9.8m/s2 [1G] (O-P)Shock (Non-operating)490 m/s2 [50G] (Half sine wave 11ms)Acoustical Noise42dB (IEC 179 A-weighted at 1m)12

PowerDC Voltage and Current Requirements5V 5%, 12V 5% 5VSleepStandbyIdleRandom Access (average)280mA300mA580mA (DVD)600mA (CD)930mA (DVD)850mA (CD) 12V0mA0mA50mA (DVD)50mA (CD)710mA (DVD)870mA (CD)PhysicalHeightWidthDepthWeight5.75" (146mm)1.6" (41.5mm)7.6" (193mm)2.18lbs (.99kg)ConnectorsDC inputAMP 1-480424-0IDE Interface Connector40 Pin ATAPI StandardAnalog Audio Line Output Connector4 Pin ATAPI Standard (70066 Series, C Version)Digital Audio Line Output Connector4 Pin ATAPI Standard (70066 Series, C Version)LasersCD LaserTypeWave LengthDVD LaserTypeWave LengthSemiconductor Laser and 3-beam System770 - 795 nmSemiconductor Laser and 1-beam System770 - 650 nmRegulatoryThe SD-M1612 DVD-ROM drive has been certified by the following regulatory agencies:13 UL 1950 CSA C22.2 No. 950 TUV (EN60950I) CE standard CB DHHS 21 CFR Sub-Chapter J BSMI

DRIVE CONNECTORS –SD-M1612Figure 1.SD-M1612 DVD-ROM Drive Rear Panel - ConnectorsPower is supplied to your DVD-ROM drive by the connection with your computer's 5V/ 12Vpower cable to the power socket at the back of drive. One side of the plug has chamferededges, so the power connector fits only one way.CAUTION: Severe damage to the Drive circuits may occur if power cable is plugged in upsidedown with power ON.AudioConnectorsSupplies Analog and Digital sound to your system.PowerConnectorATAPIConnector14The SD-M1612 DVD drive is connected to your computer system through the ATAPIconnector.

Table 1.Interface Pin AssignmentsINTERFACE PIN NDHD7HD8HD667I/OI/O89101112131415161718192015HOST SIGNAL NAMEI/OHost Data Bus BIT 7Host Data Bus BIT 8Host Data Bus BIT 6PINNO.2122232425HD9HD5Host Data Bus BIT 9Host Data Bus BIT 1HD3HD12HD2HD13HD1HD14HD0HD15GNDHost Data Bus Bit 10Host Data Bus BIT 4Host Data Bus BIT 11Host Data Bus BIT 3Host Data Bus BIT 12Host Data Bus BIT 2Host Data Bus BIT 13Host Data Bus BIT 1Host Data Bus BIT 14Host Data Bus BIT 0Host Data Bus BIT HDRQGNDHWR-,STOPGNDHRD-,HDMARDY, S16HA1PDIAGHA0HA2HCS1HCS3DASP--(KEYPIN)40-GNDHost ResetOIIHOST SIGNAL NAMEDMA RequestHost I/O WriteHost I/O ReadI/O Channel ReadyCable SelectDMA AcknowledgeHost Interrupt RequestHost 16 BIT I/OHost Address Bus BIT 1Passed DiagnosticsHost Address Bus BIT 0Host Address Bus BIT 2Host CHIP Select 0Host CHIP Select 1Drive Active/Drive 1Present

Figure 1.SD-M1612 DVD-ROM Drive Front Panel Loading Tray Load disc using tray. Busy Indicator When you install a disc into the DVD-ROM drive, the BUSY light flashes slowly as it attempts to locate the disc. One of the following will occur: BUSY light goes out. The DVD-ROM drive is ready