Transcription

Crosby Value AddedG-209Screw pin anchorshackles meet theperformancerequirements ofFederal SpecificationRR-C-271F TypeIVA, Grade A, Class2, except for thoseprovisions required ofthe contractor.G-213Round pin anchorshackles meet theperformancerequirements ofFederal SpecificationRR-C-271F TypeIVA, Grade A, Class1, except for thoseprovisions required ofthe contractor.G-2130Bolt-type anchorshackles meet theperformancerequirements ofFederal SpecificationRR-C-271F Type IVA,Grade A, Grade A,Class 3, except for thoseprovisions required ofthe contractor.G-210Screw pin chainshackles meet theperformancerequirements ofFederal SpecificationRR-C-271F TypeIVB, Grade A, Class2, except for thoseprovisions required ofthe contractor.G-215Round pin chainshackles meet theperformancerequirements ofFederal SpecificationRR-C-271F TypeIVB, Grade A, Class1, except for thoseprovisions required ofthe contractor.G-2150Bolt-type chainshackles meet theperformancerequirements ofFederal SpecificationRR-C-271F TypeIVB, Grade A, Class3, except for thoseprovisions required ofthe contractor.Copyright 2013 The Crosby Group LLCAll Rights ReservedShackles Charpy impact properties: Crosby’s Quenched and Tempered shackles have enhanced impact properties for greatertoughness at all temperatures. If requested at the time of order, Crosby can provide Charpy impact properties. Fatigue properties: Fatigue properties are available for 1/3 to 55 metric ton shackles. These Crosby shackles are fatiguerated to 20,000 cycles at 1-1/2 times the Working Load Limit. Ductility properties: Typical ductility properties are available for all sizes upon special request. Hardness levels and material tensile strengths: Typical values are available for all sizes of shackles, and actual valuescan be furnished if requested at the time of order. Proof Testing: If requested at the time of order, shackles can be furnished proof tested with certificates. Mag Certification: If requested at the time of order, shackles can be Mag inspected with certificates. Certification: Certification to World Class Standards is available upon special request at the time of order; AmericanBureau of Shipping, Lloyds Register of Shipping, Det Norske Veritas, American Petroleum Institute, RINA, NuclearRegulatory Commission, and several other world wide standards. Applications: Round Pin Shackles can be used in tie down, towing, suspension or lifting applications where the load isstrictly applied in-line. Screw Pin Shackles can be used in any application where a round pin shackle is used. In addition,screw pin shackles can be used for applications involving side-loading circumstances. Reduced working load limits arerequired for side-loading applications. Bolt-Type Shackles can be used in any application where round pin or screw pinshackles are used. In addition, they are recommended for permanent or long-term installations and where the load mayslide on the shackle pin causing the pin to rotate. Material analysis: Crosby can provide certified material (mill) analysis for each production lot, traceable by the ProductIdentification Code (PIC). Crosby, through its own laboratory, verifies the analysis of each heat of steel. Crosby purchases only special bar forging quality steel with specific cleanliness requirements and guaranteed hardenability. Field inspection: Written instructions for visual, magnaflux, and dye penetrant inspection of shackles are availablefrom Crosby. In addition, acceptance criteria and repair procedures for shackles are available. QUIC-CHECK : Shackles incorporate two marking indicators forged into the shackle bow at 45 angles from vertical.These are utilized to quickly check the approximate angle of a two-legged hitch or quickly check the angle of a singleleg hitch when the shackle pin is secured and the pull of the load is off vertical or side loaded, thus requiring a reduction in the working load limit of the shackle.75

Crosby Round Pin ShacklesROUND PINANCHORSHACKLESG-213 / S-213G-213 Round pin anchor shacklesmeet the performance requirementsof Federal Specification RR-C-271FType IVA, Grade A, Class 1, exceptfor those provisions required ofthe contractor. For additionalinformation, see page 444.G-213 / S-213G-215 / S-215 Capacities 1/2 through 35 metric tons.Forged - Quenched and Tempered, with alloy pins.Working Load Limit permanently shown on every shackle.Hot Dip galvanized or Self Colored.Fatigue rated.Shackles 25t and larger are RFID EQUIPPED.Shackles can be furnished proof tested with certificates to designatedstandards, such as ABS, DNV, Lloyds, or other certification. Charges forproof testing and certification available when requested at the timeof order. Shackles are Quenched and Tempered and can meet DNV impactrequirements of 42 joules (31 ft-lbs.) at -20 degree C (-4 degree F). Look for the Red Pin . . . the mark of genuine Crosby quality.APPLICATION INSTRUCTIONSSEE PAGE 89 OF THE GENERAL CATALOGROUND PINCHAINSHACKLESG-215 / S-215G-215 Round pin chain shacklesmeet the performance requirementsof Federal Specification RR-C-271FType IVB, Grade A, Class 1, exceptfor those provisions required ofthe contractor. For additionalinformation, see page 444.G-213 / S-213 Round Pin Anchor ShacklesWorkingStockDimensionsToleranceNominal LoadNo.Weight(in.) A1/41/21018017 1018026.13.47.31 1.13 .25.78.61 1.28 1.84 1.34 .25 .06 .065/163/41018035 1018044.18.53.38 1.22 .31.84.75 1.47 2.09 1.59 .31 .06 .063/811018053 1018062.29.66.44 1.44 .38 1.03 .91 1.78 2.49 1.86 .38 .13 .067/161-1/21018071 1018080.38.75.50 1.69 .44 1.16 1.06 2.03 2.91 2.13 .44 .13 .061/221018099 1018106.71.81.63 1.88 .50 1.31 1.19 2.31 3.28 2.38 .50 .13 .065/83-1/41018115 10181241.501.06 .75 2.38 .63 1.69 1.50 2.94 4.19 2.91 .69 .13 .061018133 1018142 2.321.25 .88 2.81 .75 2.00 1.81 3.50 4.97 3.44 .81 .25 .063/44-3/47/86-1/21018151 1018160 3.491.44 1.00 3.31 .88 2.28 2.09 4.03 5.83 3.81 .97 .25 .0618-1/21018179 1018188 5.001.69 1.13 3.75 1.00 2.69 2.38 4.69 6.56 4.53 1.06 .25 .061-1/89-1/21018197 1018204 6.971.81 1.25 4.25 1.13 2.91 2.69 5.16 7.47 5.13 1.25 .25 .061-1/4121018213 1018222 9.752.03 1.38 4.69 1.29 3.25 3.00 5.75 8.25 5.50 1.38 .25 .061-3/813-1/2 1018231 1018240 13.25 2.25 1.50 5.25 1.42 3.63 3.31 6.38 9.16 6.13 1.50 .25 .131-1/2171018259 1018268 17.25 2.38 1.63 5.75 1.54 3.88 3.63 6.88 10.00 6.50 1.62 .25 .131-3/4251018277 1018286 29.46 2.88 2.00 7.00 1.84 5.00 4.19 8.86 12.34 7.75 2.25 .25 .132351018295 1018302 45.75 3.25 2.25 7.75 2.08 5.75 4.81 9.97 13.68 8.75 2.40 .25 .13* NOTE: Maximum Proof Load is 2.0 times the Working Load Limit. Minimum Ultimate Strength is 6 times the Working LoadLimit. For Working Load Limit reduction due to side loading applications, see page 91.G-215 / S-215 Round Pin Chain 0Tolerance .06.06.06.06.13.13.13.13.13* NOTE: Maximum Proof Load is 2.0 times the Working Load Limit. Minimum Ultimate Strength is 6 times the Working LoadLimit. For Working Load Limit reduction due to side loading applications, see page 91.76Copyright 2013 The Crosby Group LLCAll Rights Reserved

Crosby Screw Pin Shackles G-209 / S-209G-209 Screw pin anchor shacklesmeet the performance requirementsof Federal Specification RR-C-271FType IVA, Grade A, Class 2, exceptfor those provisions required ofthe contractor. For additionalinformation, see page 444. Capacities 1/3 thru 55 metric tons, grade 6.Forged - Quenched and Tempered, with alloy pins.Working Load Limit and grade “6” permanently shown on every shackle.Hot Dip galvanized or Self Colored.Fatigue rated.Shackles 25t and larger are RFID EQUIPPED.Shackles can be furnished proof tested with certificates to designated standards, suchas ABS, DNV, Lloyds, or other certification. Charges for proof testing and certificationavailable when requested at the time of order.Approved for use at -40 degree C (-40 degree F) to 204 degree C (400 degree F).2t through 25t bow and screw pin are Certified to meet charpy impact testing of42 joules (31 ft-lbs.) min. ave. at -20 degree C (-4 degree F).All shackles are Quenched and Tempered and can meet DNV impactrequirements of 42 joules (31 ft. lbs.) at -20 degree C (-4 degree F).Meets or exceeds all requirements of ASME B30.26.Type Approval and certification in accordance with ABS 2006 Steel Vessel Rules1-1-17.7, and ABS Guide for Certification of Cranes.Crosby 2t through 25t G209 anchor shackles are type approved to DNVCertification Notes 2.7-1 -Offshore Containers. These Crosby shackles arestatistical proof and impact tested. The tests are conducted by Crosby and 3.1test certification is available upon request.Look for the Red Pin . . . the mark of genuine Crosby quality.G-209 / S-209 Screw Pin Anchor ShacklesG-209 / S-209G-210 / 69.441.88.502.38 .632.81 .753.31 .883.75 1.004.25 1.164.69 1.295.25 1.425.75 1.547.00 1.847.75 2.0810.50 2.71SCREW PINCHAINSHACKLESG-210 / S-210G-210 Screw pin chain shacklesmeet the performance requirementsof Federal Specification RR-C-271F,Type IVB, Grade A, Class 2, exceptfor those provisions required ofthe contractor. For additionalinformation, see page 11.281.84.751.47 2.09.911.78 2.491.06 2.03 2.911.19 2.31 3.281.50 2.94 4.191.81 3.50 4.972.09 4.03 5.832.38 4.69 6.562.69 5.167.473.00 5.75 8.253.31 6.38 9.163.63 6.88 10.004.19 8.86 12.344.81 9.97 13.685.69 12.87 17.84ShacklesSCREW PINANCHORSHACKLESTolerance /LMP.16 1.14 .19.19 1.43 .25.22 1.71 .31.25 2.02 .38.31 2.37 .44.38 2.69 .50.44 3.34 .69.50 3.97 .81.50 4.50 .97.56 5.13 1.06.63 5.71 1.25.69 6.25 1.38.75 6.83 1.50.81 7.33 1.621.00 9.06 2.251.22 10.35 2.401.38 13.00 13.13.25G-210 / S-210 Screw Pin Chain ShacklesWorkingStockDimensionsToleranceNominal LoadNo.Weight(in.) A1/41/21019150 1019169.11.47.31.25.25.97.62.971.59.191.43 .06 .065/163/41019178 1019187.17.53.38.31.31 1.15 .75 1.07 1.91.221.71 .06 .063/811019196 1019203.28.66.44.38.38 1.42 .92 1.28 2.31.252.02 .13 .067/161-1/21019212 1019221.43.75.50.44.44 1.63 1.06 1.48 2.67.312.37 .13 .061/221019230 1019249.59.81.63.50.50 1.81 1.18 1.66 3.03.382.69 .13 .065/83-1/41019258 10192671.251.06 .75.63.63 2.32 1.50 2.04 3.76.443.34 .13 .061019276 1019285 2.631.25 .88.81.75 2.75 1.81 2.40 4.53.503.97 .25 .063/44-3/47/86-1/21019294 1019301 3.161.44 1.00 .97.88 3.20 2.10 2.86 5.33.504.50 .25 .0618-1/21019310 1019329 4.751.69 1.13 1.00 1.00 3.69 2.38 3.24 5.94.565.13 .25 .061-1/89-1/21019338 1019347 6.751.81 1.25 1.25 1.13 4.07 2.69 3.61 6.78.635.71 .25 .061-1/4121019356 1019365 9.062.03 1.38 1.38 1.25 4.53 3.00 3.97 7.50.696.25 .25 .131-3/813-1/2 1019374 1019383 11.63 2.25 1.50 1.50 1.38 5.01 3.31 4.43 8.28.756.53 .25 .131-1/2171019392 1019409 15.95 2.38 1.63 1.62 1.50 5.38 3.62 4.87 9.05.817.33 .25 .131-3/4251019418 1019427 26.75 2.88 2.00 2.12 1.75 6.38 4.19 5.78 10.97 1.00 9.06 .25 .132351019436 1019445 42.31 3.25 2.25 2.36 2.10 7.25 5.00 6.77 12.74 1.13 10.35 .25 .132-1/2551019454 1019463 71.75 4.12 2.75 2.63 2.63 9.38 5.68 8.07 14.85 1.38 13.00 .25 .25* NOTE: Maximum Proof Load is 2.0 times the Working Load Limit. Minimum Ultimate Strength is 6 times the Working LoadLimit. For Working Load Limit reduction due to side loading applications, see page 91.Copyright 2013 The Crosby Group LLCAll Rights Reserved77

Crosby Alloy Screw Pin ShacklesAPPLICATION INSTRUCTIONSSEE PAGE 89 OF THE GENERAL CATALOGG-209AG-209A Screw pin anchor shacklesmeet the performance requirementsof Federal Specification RR-C-271FType IVA, Grade B, Class 2, exceptfor those provisions required ofthe contractor. For additionalinformation, see page 444. Capacities 2 thru 21 metric tons. Meets performance requirements ofGrade 8 shackles. Forged Alloy Steel – Quenched and Tempered, with alloy pins. Working Load Limit permanently shown on every shackle. Hot Dip Galvanized. Shackles can be furnished proof tested with certificates to designatedstandards, such as ABS, DNV, Lloyds, or other certification. Charges forproof testing and certification available when requested at the time of order. Approved for use at -40 degree C (-40 degree F) to 204 degree C(400 degree F). Meets or exceeds all requirements of ASME B30.26 includingidentification, ductility, design factor, proof load and temperaturerequirements. Importantly, these shackles meet other criticalperformance requirements including fatigue life, impact properties andmaterial traceability, not addressed by ASME B30.26.G-209A Crosby Alloy Screw Pin 1/2151821G-209AStock .812.092.382.693.003.31Tolerance 13* Maximum Proof Load is 2 times the Working Load Limit (metric tons) and 2.2 times the Working Load Limit (short tons). Minimum Ultimate Strength is 4.5 timesthe Working Load Limit for metric tonnes, and 5 times the Working Load Limit for short tons. For Working Load Limit reduction due to side loading applications,see page 91.APPLICATION INSTRUCTIONSSEE PAGE 89 OF THE GENERAL CATALOGG-2169S-2169 Capacities of 7, 12.5 and 18 metric tons.Quenched and Tempered for maximum strength.Forged Alloy Steel.Available in galvanized and self colored finished.Individually proof tested and magnetic particleinspected. Crosby certification available at time of order. Meets or exceeds all requirements of ASME B30.26including identification, ductility, design factor, proofload and temperature requirements. Importantly, theseshackles meet other critical performance requirementsincluding fatigue life, impact properties and materialtraceability, not addressed by ASME B30.26. Look for the Red Pin . . . the mark of genuineCrosby quality.G-2169 / S-2169 Screw Pin “Wide Body” G-2169S-2169Stock No. Stock tEach(lbs.)3.58.813B /.251.251.692.03C.69.921.16D .25P4.105.516.76R5.877.639.38* Ultimate Load is 5 times the Working Load Limit. Forged Alloy Steel. Proof Load is 2 times the Working Load Limit.78Copyright 2013 The Crosby Group LLCAll Rights Reserved

Crosby Bolt Type Shackles G-2130 / S-2130 G-2130 Bolt Type Anchor shackleswith thin head bolt - nut with cotter pin. Meets the performancerequirements of FederalSpecification RR-C-271F Type IVA,Grade A, Class 3, except for thoseprovisions required of the contractor.For additional information, seepage 444. G-2130 / S-2130G-2150 / S-2150Capacities 1/3 thru 150 metric tons, grade 6.Working Load Limit and grade “6” permanently shown on every shackle.Forged – Quenched and Tempered, with alloy pins.Hot Dip galvanized or Self Colored. (85, 120, and 150 metric ton shacklesare all hot dip galvanized bows and the bolts are Dimetcoted and painted red)Fatigue rated (1/3t - 55t).Shackles 25t and larger are RFID EQUIPPED.Approved for use at -40 degree C (-40 degree F) to 204 degree C (400 degree F).Meets or exceeds all requirements of ASME B30.26.Shackles 85 metric tons and larger are individually proof tested to 2.0 times theworking load limit.Shackles 120 metric tons and larger are proof tested, Magnetic Particle Inspected andprovided with Serialized Pin and Bow.Type Approval and certification in accordance with ABS 2006 Steel Vessel Rules1-1-17.7, and ABS Guide for Certification of Cranes.3.1 Certification as standard available for charpy and statistical proof test for pg 79only up to 25 tons to DNV2.7-1 and EN13889.Crosby 2t through 25t G2130 anchor shackles are type approved to DNV CertificationNotes 2.7-1- Offshore Containers. These Crosby shackles are statistical proof andimpact tested to 42 joules (31 ft-lbs.) min. ave. at -20 degree C (-4 degree F). The testsare conducted by Crosby and 3.1 test certification is available upon request. Refer topage 76 for Crosby COLD TUFF shackles that meet the additional requirements ofDNV rules for certification of lifting applications - Loose Gear.All other 2130 and all 2150 shackles can meet charpy requirements of 42 joules(31 ft-lbs) avg at -20 degree C (-4 degree F) upon special request.Look for the Red Pin . . . the mark of genuine Crosby LoadLimit(t)*1/3 7253555† 85† 120 ‡† 150 98.25154.00265.00338.00BOLT TYPECHAINSHACKLESG-2150 / S-2150G-2150 Bolt Type Chain shackles.Thin hex head bolt - nut withcotter pin. Meets the performancerequirements of FederalSpecification RR-C-271F TypeIVB, Grade A, Class 3, exceptfor those provisions required ofthe contractors. For additionalinformation, see page 13.634.194.815.696.508.009.00Tolerance ominal LoadNo.Weight(in.) /SizeLimitEach(in.)(t)*G-2150 221019775 83-1/41019793 10198001.471.06.77.631.502.04 3.76 2.32 3.56.63.13.062.40 4.53 2.75 4.15.81.25.063/44-3/41019819 10198282.521.25.89.751.817/86-1/21019837 10198463.851.441.02.882.102.86 5.33 3.20 4.82.97.25.0618-1/21019855 10198645.551.691.151.002.38 3.24 5.94 3.69 5.391.00.25.061-1/89-1/21019873 10198827.601.811.251.132.68 3.61 6.78 4.07 5.901.25.25.061-1/4121019891 1019908 10.812.031.401.253.00 3.977.504.53 6.691.38.25.061-3/813-1/2 1019917 1019926 13.752.251.531.383.31 4.43 8.285.017.211.50.25.131-1/2171019935 1019944 18.502.381.661.503.62 4.87 9.05 5.387.731.62.25.131-3/4251019953 101996231.402.88 2.041.754.19 5.82 10.97 6.38 9.33 2.12.25.13.132351019971 1019980 46.753.25 2.302.105.00 6.82 12.74 7.25 10.41 2.36.252-1/2551019999 1020004 85.004.12 2.80 2.63 5.68 8.07 14.85 9.38 13.58 2.63.25.253† 851020013–124.255.00 3.25 3.00 6.50 8.56 16.87 11.00 15.13 3.50.25.25* NOTE: Maximum Proof Load is 2.0 times the Working Load Limit. Minimum Ultimate Strength is 6 times the Working LoadLimit. For Working Load Limit reduction due to side loading applications, see page 91.† Individually Proof Tested with certification.‡ Furnished in Anchor style only and furnished with Round Head Bolts with welded handles.Copyright 2013 The Crosby Group LLCAll Rights ReservedShacklesBOLT TYPEANCHORSHACKLES79

Crosby Alloy Bolt Type ShacklesAPPLICATION INSTRUCTIONSSEE PAGE 89 OF THE GENERAL CATALOGG-2130A ALLOYBOLT TYPESHACKLESGRADE 80G-2130ABolt Type Anchor shackles withthin head bolt – nut with cotterpin. Meets the performancerequirements of FederalSpecification RR-C-271F TypeIVA, Grade B, Class 3, exceptfor those provisions required ofthe contractor. For additionalinformation, see page 444. Capacities 2 to 17 metric tons. Working Load Limit permanently shown on everyshackle. Forged Alloy Steel – Quenched and Tempered, withbow and bolt. Hot Dip galvanized. Shackles can be RFID EQUIPPED. Meets or exceeds all requirements ofASME B30.26 including identification, ductility,design factor, proof load and temperaturerequirements. Importantly, these shackles meet othercritical performance requirements including impactproperties and material traceability, not addressed byASME B30.26. Shackles can be furnished proof tested withcertificates to designated standards, such as ABS,DNV, Lloyds, or other certification when requestedat time of order. Type Approval and certification in accordance withDNV Type Approval under DNV 2.7-1. Shackles are Quenched and Tempered and meetsDNV impact requirements of 42 joules (31 ft. Ibs.) at-40 degree C (-40 degree F).G-2130A Alloy Bolt Type Shackles Grade 3-1/217G-2130AStock 3.253.623.88Tolerance .060.060.060.060.130.13* NOTE: Maximum Proof Load is 2.0 times the Working Load Limit. Minimum Ultimate Strength is 8 times the Working Load Limit.For Working Load Limit reduction due to side loading applications, see page 91.80Copyright 2013 The Crosby Group LLCAll Rights Reserved

Charpy impact properties: Crosby’s Quenched and Tempered shackles have enhanced impact properties for greater toughness at all temperatures. If requested at the time of order, Crosby can provide Charpy impact properties. Fatigue properties: Fatigue properties are available for 1/3 to 55 metric ton shackles