mopdf.com

Maintenance History Continued for Equipment ID: RDC044Start DateJob Number / DescriptionMeter Reading (Hrs)BI-WEEKLY OCT 10 - OCT 23, 12As per discussion with Chris McNeil & Julio, these won is to be closed.30/4/13 CCOCT 10/12- JIM MACFARLANEPICK UP PARTS TRAVEL TO SITE, INSTALL COOLING, FILLED WITH OIL RAN UNIT NO LEAKS,REMOVED DAMAGED DOOR POUCH, NEED LONG RIVETS TO INSTALL NEW POUCHOCT 13/12- STEPHEN CHERRYCOMPLETE TIRE REPORT, SEE SHEET, COMPLETE OUTSEET, REPAIR ON OUTSHEET TO BE COMPETEDINSTALL RH POCKET ON DOOR CLEAN CAB TOOK PHOTOS , PARTS TO BE ORDEREDOCT 16/12- DON PELLERINDID RUNNING CHECKS A OK ON EVERYTHINGOCT 18/12- JIM MACFARLANEPICK UP PARTS, TRAVEL TO SITE, START UNIT WARMED UP, TOOK OIL SAMPLES, INSTALLED DOORPOCKET REPLACED PANEL SCREWS, SECURED REGULATOR FOR GREASERS, INSTALLED CAB FOAM,REMOVED FORT MCKAY DECALSOCT 20/12- JIM MACFARLANEOUTSHEET INSPECTIONS CHECKS, VERY BAD CONDITIONS , CAB NEED CLEAININ TO MUCH MUDOCT 21/12- KEVIN LOWCHECK TRUCKS IN OTHER YARD FOUND 2 DIFF GUARDS TRAVEL TO B/M TO CHECK UNIT TO MAKESURE OF WITCH ONE IT HAD BUILD GUARD AND PAINT, CLEAN UPOCT 22/12- KEVIN LOWOUT SHEET INSPECTION REPAIRS, FIX A FEW SMALL OIL LEAKS, CHANGE STEERING AND HYDFILTERS TAKE OIL SAMPLES OF BOTH, INSTALL GUARD ON HYD TANK FOR TANK HEATERS CHEKOVER UNIT25-Sep-2012WOC154873 - BI-WEEKLY SEPT 26 - OCT 09, 12Emeco Canada Limited GST Registration # 104545959RTweb www.emecogroup.com23,407Page 7 of 31Printed on: 12-Jan-2016

Maintenance History Continued for Equipment ID: RDC044Start DateJob Number / DescriptionMeter Reading (Hrs)BI-WEEKLY SEPT 26 - OCT 09, 12OCT 3/12- ANDREW MACDONALDASSESS HAZARDS AND COMPLETE JHA COMPLETE JHA COMPLETE IN SHEET WITH EXCEPTION OFOIL SAMPLES AND RUNNING CHECKS BATTERY DEADOCT 4-12 GRANT OSMANTRAVEL TO UNIT, DRAG OUT BOOST CABLES, HOOK UP TO BOOST, NOTICED LIGHT ON WITHMASTER SWITCH OFF, SOURCE A MASTER SWITCH, ATTEMPTED TO BOOST, WOULDNT CRANK OVER,NO POWER FLOW AT BOOST RECIEVER, END OF SHIFT NO SHOOTING DONE, STEAM CLEANMECHANIC TRUCK AT SHOPOCT 4-12 THOMAS HOERBERDROVE TO SYNCRUDE BM, JHA, LOCKOUT,CHOCKBLOCKS, TOOK OIL SAMPLES AND AF SAMPLE,CHECKED OVER ELECTRIC SYSTEM, BATTERY CONTACTS VOLTAGE ON OUTER, BATTERIES 8.3, INNER12.3 VOLT, NEED 2 NEW BATTERIES, BOOSTED TO START WITH HELP OF OTHER 777, TEST RUNTRUCK, CHECK LIGHTS, BRAKES, RUNING CHECKS, DROVE BACK TO SHOP, FINISH PAPER WORK FOROIL SAMPLES, WRITE REPORTOCT 5/12- ANDREW DONALDTRAVEL TO BASEMINE COMPLETE JHA REVIEW DEFECTS REMOVE INSTRUMENTS WARNING CLUSTERCHANGE OUT STICKER INSTALL NEW WARNING CLUSTER CHECK HOIST VALVE LEAKS REPLACE 3O-RINGS ON HOIST VALVE REMOVE R/H LADDER AND REPAIR, BENT BRACKET BROKEN BOLT INBRACKET DRILL AND TAP HOLE, INSTALL LADDER TIGHTEN UP LOOSE HAND RAIL BOLTS TIE UPLOOSE WIRES ON R/H SIDE OF ENGINE CHECK OUT OIL LEAK @ DIFF PLUG A BIT LOOSE BUT OILAPPEARS TO HAVE BEEN FROM SERVICE TIGHTEN UP LOOSE HEADLIGHT ON RH FENDER CLEAN UPTOLLS AND EQUIPMENT AND TRAVEL TO SHOPOCT 5/12- PAUL HICKSTHE TWO OUTSIDE BATTERIES WERE COMPUND AND REMAINING TWO PUT TOGETHER AS A SET, IRETURNED TO THE SHOP AND GET TWO MORE BATTERIES THESES WERE INSTALLED THE JUMPERCABLE BETWEEN THE BATTERIES WERE ORDERED, THERE IS A LEAK ON A BRAKE COOLING TUBEAND THE HOIST VALVE PARTS ARE ORDEREDOCT 5/12-JIM MACFARLANECHECKED MACHINE NO START SWITCHED BATTERIES GROUND TO MAKE ONE GOOD, STARTED UNITMOVED OUT OF MUD, CLEANED MUD FROM VALVE AND BRAKE COOLING LINES, RAN UNIT , OILLEAKING FROM WELDED FOR RIGHT BRAKE COOLING TUBE ORDERED PARTSOCT 7/12- PAUL HICKSREMOVED SOME HYD LINES TO ACCESS THE MAIN VALVE TO REPAIR A LEAK ON THE CONTROLVALVE INSTALLED THE LINES WITH NEW O-RINGSOCT 7-12 PAUL HICKSTHE DRIVE LINE WAS MOVED OUT OF THE WAY AND THE YOKE REMOVED AND THE TORQUE OUTPUTSEAL REPLACED, THE YOKE WAS PUT BACK IN BUT NOT TORQUED IN PLACE BECAUSE I HAD TOGOTO ANOTHER UNITOCT 8/12- JIM MACFARLANESEARCHED FOR PARTS AROUND SHOP, TRAVEL TO SITE INSTALL BATTERY CABLES, STARTED UNITAND MONITOR WAS FLASHING AND ALARM SOUNDING ECM HAD LOST ITS PROGRAM REFLASHEDMONITOR ECM AND SET HOURS OK, WARMED UNIT CLEANED CONTROL VALVE REMOVED LINESRESEALED LINES, RAN UNIT AGAIN NO LEAKOCT 9-12 CARLS LEATHERSREPLACED BATTERIES AND REPAIRED WIRING, REPLACED COOLING TUBE TO LEFT REAR BRAKEOCT 5/12-FINNINGLIFTED NEW BATTERIES ON TOP OF TRUCK AND ISNTALLED INTO POCKET BOLTED DOWN CLAMPAND INSTALLED CABLES JUMPER CABLE HAD ONE OF THE ENDS BROKEN NOTIFIED CUSTOMER TOORDER NEW ONE LIFTED OLD BATTERIES DOWN OFF OF TRUCK TRAVELLED BACK TO SHOPOCT 10/12- MELVIN bUTLERCLEAN INTERIOR OF CABS, CLEAN FLOOR AND GLASSEmeco Canada Limited GST Registration # 104545959RTweb www.emecogroup.comPage 8 of 31Printed on: 12-Jan-2016

Maintenance History Continued for Equipment ID: RDC044Start Date11-Sep-2012Job Number / DescriptionMeter Reading (Hrs)WOC152821 - BI-WEEKLY SEPT 13 - SEPT 26,1223,385BI-WEEKLY SEPT 13 - SEPT 26,1As per discussion with Chris McNeil & Julio, these won is to be closed.30/4/13 CC229-Aug-2012WOC150615 - BI-WEEKLY AUG 29 - SEPT 12, 1223,357BI-WEEKLY AUG 29 - SEPT 12, 1As per discussion with Chris McNeil & Julio, these won is to be closed.30/4/13 CC2AUG 29/12- GRANT OSMANLOCK CHOCK, FLRA, CHECK TEST STARTERS BOTH WORKING , REMOVE COVERS FOR BATTREY,FOUND ON BATTERY CABLE OFF FOR LEFT BATTERYS REPAIRED POST AND CABLE EYE TESTWORKING GOOD.25-Aug-2012WOC217037 - PERFORM ENGINE VALVE SET23,357.15-Aug-2012WOC148720 - BI-WEEKLY AUG 15-28 VALVE SET)23,052BI-WEEKLY AUG 15 - AUG 28, 12AUG 21/12- KEVIN LOWCHECK ROLO CHAMBERS AND OVER STROKE SWITCHES , RUN TRUCK UP TO TEMP, CHECK VIMS NOACTIVE CODES , SEND TRUCK TO WORKAUG 25/12FOUND MUD FLAPS, CODES LOGGED, TEST SWITCH BROKEN, DIFF LOW, FOUNDI LEAKING CYLINDERHEADS ON LEFT FRONT CORNER RAD PLUGGED, ADVISED SHOP SUPERVISORAUG 25/12- GRANT OSMANTRAVEL TO SYNCUDE ESCORT LUBE TRUCK TO LAYDOWN ATTEMPT TO FINE MACHINE AT WI DUMPBUT ROADS TO ACCESS NOW DUG UP UNABLE TO FIND ROTTI THROUGH MINE AND UP RAMP,TRAVEL TO FT MCKAY LAYDOWN AND WAIT FOR ESCORT, ESCORT OUT VIA SW SANDS, FLRA ANDLOCKS AND CHOCKS, DIG MUD OUT OF ENGINE TIMING AREA PIN, ENGINE WOULDN'T PIN TURNEDOVER SEVERAL TIMES VALVE AND INJECTOR SET, REPAIR COOLANT LEAK AT ENGINE FPUND LOOSEPLUG UNDER REAR AFTER CODER TRANS RADIATOR REMOVED PLUG INSTALLED NEW O-RINGSREASSEMBLE , TOPPED UP COOLANT ABOUT 10L, PACK UP AND TRAVEL OFF SITEAUG 27/12- GRANT OSMANREWRITE OUT VALVE SET SHEET TIME AND PAPER WORKAUG 26/12- MELVIN BUTLER2000HR SERVICEAUG 26/12- TYLER MACEACHERN2000 HR SERVICEAUG 27/12- LEE MEISEREFILL OILS BACK INTO LUBE TRUCK, OFF LOAD USE OIL AND FILTERS FROM LUBE TRUCK, FUEL UPLUBE TRUCK, GATHER UP AND PUT FILTER KITS INTO LUBE TRUCK, CLEAN TRASH FROM LUBE TRUCKAUG 27/12- GRANT OSMANTRAVEL TO MACHINE CARRY OUT INSPECTION ON MACHINE CLEAN UP MESS LEFT ON DECK BYSERVICE CREW, REPAIR ONE LIGHT BULB BLOWN HIGH BEAM, PACK UP OFF JOB, TIDY WIRING ONREAR BOX LIGHTS HEAT SHRINK EXPOSED WIRE31-Jul-2012WOC146726 - BI-WEEKLY AUG 01- AUG 14, 120BI-WEEKLY AUG 01- AUG 14, 1217-Jul-2012WOC144488 - BI-WEEKLY JULY 18 - 31, 2012Emeco Canada Limited GST Registration # 104545959RTweb www.emecogroup.com0Page 9 of 31Printed on: 12-Jan-2016

Maintenance History Continued for Equipment ID: RDC044Start DateJob Number / DescriptionMeter Reading (Hrs)BI-WEEKLY JULY 18 - 31, 2012As per discussion with Chris McNeil & Julio, these won is to be closed.30/4/13 CCJULY 25/12- AARON CGO TO FINNING , GET HOSE MADE, PICK UP PARTS, DELIVER TO BASE MINEJULY 25/12- STEPHEN CHERRYFLRA, CHECK A/C PRESSURES, FOUND HOLE IN A/C LINE , ORDERED, REPAIRED BROKEN WIRE TOHORN SWITCH, CLEANED UP CONTACTS ON COLUMN, HORN GOOD, GOT HOSE, INSTALLED, EVAC,VACCUM, FILL TEST GOOD4-Jul-201220-Jun-2012WOC142432 - BI WEEKLY WORK ORDERS04/07/12 to 17/07/1222,831WOC140188 - BI-WEEKLY WORK ORDER22,831Bi-Weekly Work Order 20-06-12As per discussion with Chris McNeil & Julio, these won is to be closed.30/4/13 CC TO 03-07-1219-Jun-2012WOC140070 - CHECK PARK BRAKE UPDATE22,831CHECK FOR CORRECT VALVEON PARK BRAKE VALVE5-Jun-2012WOC137932 - BI-WEEKLY JUN 06 - JUN 20, 1222,831BI-WEEKLY JUN 06 - JUN 20, 12JUNE 18/12- MIKE SCHMIDINSPECT UNIT FOR THE CORRECT PARK BRAKE RELEASE VALVE, REMOVED REAR CAB PANEL FOUNDTHT THESE ARE THE CORRECT VALVE INSTALLED28-May-2012WOC136172 - FRONT BRAKES22,794REPLACE FRONT PADS BRAKESMAY 30/12- DALE HORDALR&r FRONT BRAKE PADSMAY 31/12- ED SFO TO UNIT AND START BOARD AIR RUN AT 1500RPM TO BLEED BRAKES LET CYCLE EVERY TIME,BRAKES WERE RELEASED HAD NO OIL FROM ABOUT 2 MIN. THEN STARTED TO HAVE OILK COMINGOUT TOOK ABOUT 1 HR TO GET BRAKES BLEED PROPERLYMAY 30/12- DALE HREPLACE FRONT BRAKES22-May-2012WOC135058 - BI-WEEKLY MAY 23 - JUNE 05, 1222,783BI-WEEKLY MAY 23 - JUNE 05, 1As per discussion with Chris McNeil & Julio, these won is to be closed.30/4/13 CC2MAY 23/12- DARREN FCHECKED FOR EXCESSIVE PLAY IN STEERING , FOUND LEFT OUTER STEERING CYL. BALL STUD TOBE A BIT LOOSE BUT STILL IN SPEC, REMAINING COMPONENTS ARE IN GOOD CONDITIONJUNE 2/12- DALE HORDALCHECK MAIN SOLENOID TO CAB OK, CHECK ALL CONNECTIONS AND BATTERY, MASTER SWITCH,FOUND JUMOER BATTERY CONNECTION OFF, LOOSE CONNECTIONS AT OTHER SET OF BATTERIES,REMOVE COVER UNDER WINDSHIELD AND FIND AIR LEAK LEAKING AIR WHEN RETARDER ONJUEN 3/12- DARREN JEFFERIESDROVE TO UNIT AND SET UP , CHECKED FOR RETARDER LEAKING IN DASH, WASH NOT LEAKING ,RAN TRUCK AND CHECKED FOR POWER LOSS AT DASH ACTED UP SEVERAL TIMES REMOVED DASHAND REAR OF CAB, CHECKED ALL GROUND NOTHING LOOKED WRONG CLEANNED UP CAB MAINGROUND AND REASSEMBLED IT RAN TRUCK AND DROVE IT AROUND YARD, COULD NOT GET IT TOACT UP CLEANNED UP19-May-2012WOC134714 - SWITCH TIRES AROUND22,783match tires from front to rear to match radials and bias ply8-May-2012WOC133799 - BI-WEEKLY MAY 09 - MAY 22, 12Emeco Canada Limited GST Registration # 104545959RTweb www.emecogroup.com22,783Page 10 of 31Printed on: 12-Jan-2016

Maintenance History Continued for Equipment ID: RDC044Start DateJob Number / DescriptionMeter Reading (Hrs)BI-WEEKLY MAY 09 - MAY 22, 12As per discussion with Chris McNeil & Julio, these won is to be closed.30/4/13 CCMAY 15/2-THOMSA HOERBERLOAD TOOLS AND EQUIPMENT ONN TRUCK DROVE TO SUNCOR NORTHGATE PREPARE DHA LOCKOUTTRUCK. PLACE CHOCK BLOCKS UNDER WHEEL. TROUBLE SHOOT AIR LEAK FOUND RELOGS VALUEIS LEAKING LOOKUP PARTS AND ORDER PARTSREAD OUT ECM'S FOUND BROKEN WIRE CODE STARTED TROUBLESHOOTINGCHECK OVER TRUCK CLEAN CAB TAKE PICTURESMAY 16/12-RYAN ELLISCONNECT FT CHECK CODES SWAP MONITORING DISPLAY OUT OF ANOTHER TRUCK, CODE WENTAWAY NEED TO ORDER MONITOR24-Apr-2012WOC132308 - BI-WEEKLY APR 25 - MAY 08, 1222,580BI-WEEKLY APR 25 - MAY 08, 12As per discussion with Chris McNeil & Julio, these won is to be closed.30/4/13 CC22-Apr-2012WOC132054 - 1200 HOUR FIRE SUPPRESSION PM22,673carry out 1200 hour fire suppression pm11-Apr-2012WOC131118 - BI-WEEKLY APR 11 - APR 24, 1222,586BI-WEEKLY APR 11 - APR 24, 12As per discussion with Chris McNeil & Julio, these won is to be closed.30/4/13 CCAPR.15.2012-DAN HDRIVE TO FINNING AND PICK UP PARTS,DRIVE TO UNIT IN BACK OF TAILING,CHANGE BALL STUDCHANGEL/H INNER STEER CYCLE.CHANGE R/H MIRROR,BOLTS BROKEN IN SUPPORT ARMS.PULL OFFDRILL AND TOP HOOK.FIND LARGE LUMP JAMMED BETWEEN RIGHT REAR STUDS.MOVE TRUCK HOOKUP STRAP AND GET DOZER TO PULL OUTAPR.24.2012-DAN HCHECK UNIT FOR NO HEAT, FIND PROBLEM WITH HEAER CONTROL CALL ENDS PERTS29-Mar-2012WOC129290 - BI-WEEKLY MAR 28, - APR 10, 1222,364BI-WEEKLY MAR 28, - APR 10, 1As per discussion with Chris McNeil & Julio, these won is to be closed.30/4/13 CC2APR.5.2012-MARK FFIELD INSPECTION,DEFECFT LIST,TIRE REPORTAPR.6.2012-MARK FMADE PARTS LIST FOR MACHINEAPR.5.2012-JIM MMACHINE INSPECTION/TIRE SURVEY14-Mar-2012WOC126591 - BI-WEEKLY MAR 14 - MAR 27, 1222,364BI-WEEKLY MAR 14 - MAR 27, 12As per discussion with Chris McNeil & Julio, these won is to be closed.30/4/13 CC29-Feb-2012WOC124331 - C/O TIRES22,113c/o out tires27-Feb-2012WOC123860 - BI-WEEKLY FEB 29 - MAR 13, 12Emeco Canada Limited GST Registration # 104545959RTweb www.emecogroup.com22,429Page 11 of 31Printed on: 12-Jan-2016

Maintenance History Continued for Equipment ID: RDC044Start DateJob Number / DescriptionMeter Reading (Hrs)BI-WEEKLY FEB 29 - MAR 13, 12MAR 2, 2012 - JERAMEY SC/O RADDIG OUT RADIATOR FROM COLT TENT AND LOAD ON LEDCOR TRUCK.MAR 4, 2012 - MARK FREPLACE RADLEFT SHOP HEADED TO SITE. STARTED TO REMOVE PANELS AND ASSEMBLIES. PARTS ARE ATMACHINE.MAR 5, 2012 - KEVIN LINDSAYREPLACE RADDRIVE TO AND FROM SUNCOR. GET MINE ENTERY FORM, SIGN IN AND OUT AT LEDCOR OFFICE.DRIVE TO MACHINE INSTALLED RAD.MAR 6, 2012 - KEVIN LINDSAYINSTALL RADDRIVE TO AND FRON SUNCOR. GET MINE ENTERY FORM SIGN IN AND OUT AT LEDCOR OFFICETRAILER, INSTALL RAD, RUN CHECKED FOR LEAKS, WAS OK.MAR 6, 2012 - MARK FINSTALL RADINSTALL RAD AND GUARDS. LEDCOR FILLED WITH COOLANT, STARTED AND CHECK CALLED UP.23-Feb-2012WOC123466 - REPLACE SEAT BASE22,378replace seat baseQTM3331FEB 23, 2012- DAN HEINEMISSING PARTSLOOK THROUGH TENT FIND NEW SEAT BASE. CLIMB UP AND GRAB LKOAD UP DRIVE TO OIL ATTRUCK PERMIT AND SIGN IN. DRIVE TO UNIT, BOOST AND START TRUCK TO MOVE FOR TIRE GUYS.HOIST UP AND INSTALL SEAT BASE, BOLT DOWN AND HOOK UP AIR LINE. INSTALL CUSHIONREASSEMBLY. GET OTHER MISSING PART HAD TO LOOK UP PART #'S . INSTALL CONTROL VALVEBOLT AND NUTS.14-Feb-2012WOC122300 - BI-WEEKLY FEB 15 - FEB 22, 1222,379BI-WEEKLY FEB 15 - FEB 22, 12FEB 20, 2012 - DAN HEINEROBBED PARTSSTART PUTTING ROBBED PARTS BACK ON UNIT. INSTALL HYD FITTINGS AND HOOK UP HOSES.INSTALL FUEL PUMP. GO TO PUT SHOCK ON SEAT BASE. NO BASE IN CAB. DRIVE BACK TOLAYDOWN. FIND BASE IN C-CAN. PULL SHOCK OUT, FIND NEW ONE IS WORNG. LOOK UP ANDORDER PROPER SHOCK. DRIVE BACK TO SHOP.FEB 22, 2012 - DAN HEINEDOWN FOR TIRES. PARTS BEEN ROBBED OFF.CHECK OVER TRUCKS, TRY TO START. NEEDED TO BOOST. GET TRUCK STARTED. PINCH OFF AIRLINES BUILD AIR. WARM UP TRUCK AND MOVE FOR TIRE GUYS. INSTALLED DOG BONE BOLT ANDTORQUE. LOAD UP KAL TIRE JACK AND BRING BACK TO KAL.FEB 24, 2012 - DAN HEINESTART TRUCK OR KAL TIRE TO DO TIRE SWAP. KAL CANCELLED. SHUT UNIT BACK OFF.FEB 25, 2012 - KEVIN LINDSAYFIND TIRESEARCH YARD FOR TIRE AND USE LOADER TO MOVE TIRE FOR TIRE COMPANY TO PICK UP.FEB 25, 2012 - DAN HEINETIRES, DEFECTS, ROBBED PART.START TRUCK FOR KAL TO MOVE. INSTALL HOIST HOSE ON RH SIDE WHEN IT COMES IN.FEB 26, 2012 - DAN HEINEDRIVE TO SIRE, CALL IN TRUCK. DO TIRE REPORT ON UNIT WHEN IT SHOWS UP. SEND BACK TOWORK.1-Feb-201231-Jan-2012WOC120445 - BI-WEEKLY FEB 02 - FEB 14, 12BI-WEEKLY FEB 02 - FEB 14, 12As per discussion with Chris McNeil & Julio, these won is to be closed.30/4/13 CC21,368WOC120030 - STARTER CORE22,077starter coreEmeco Canada Limited GST Registration # 104545959RTweb www.emecogroup.comPage 12 of 31Printed on: 12-Jan-2016

Maintenance History Continued for Equipment ID: RDC044Start DateJob Number / Description30-Jan-2012WOC119697 - AIR DRYER/BRAKE ISSUEMeter Reading (Hrs)22,077air dryer / brake issueJAN 29, 2012 - DAN HEINEFIND REFILL KIT IN SHOP AND REBUILD AIR DRYER. DRIVE TO UNIT AND INSTALL. UNIT WASDEAD, HAD TO BOOST. START CHECKIN TRANS NEUTRALIZER LIGHT WORKING BACKWARDS NOTWORKING AT ALL. START CHECKING WIRING. FIND DIODE IN E-BAY. HAD BEEN INSTALLEDBACKWARDS. CHANGE AROUND AND CHECK ALL OK. START CHECKING BREAKE SYSTEM. AIRBUILT UP THEN FROZE UP. RUN METHYL IN BOTTOM TANK. TRY CHANGING GOVENOR. NEED TOGET HEAT TO TO TIP AIR LINE, RAN OUT OF TIME. LET CUSTOMER KNOW WHERE I LEFT OFF.27-Jan-2012WOC119362 - RELIEF VALVE LEAK21,368relief valve has l;eakJAN 25, 2012 - DAN HEINEDRIVE TO SITE, SIGN IN, GO TO LAYDOWN AND CALL IN TRUCK. BLOW OFF SAND AND DIRT, CLEANVALVE AND RUN BOX CANT FOND A LEAK. CHECK UNIT FOR NO STARTKEY IN SHUT OFF. FINDBATTERY CLAMPS HAD FALLEN OFF BATTERY., CHECK ANBD TIGHTEN ALL CONNECTIONS. SEND TOWORK AND TO CALL IN WHEN IT HAD WORKED FOR A BIT. LRAK IS ON TOP OF VALVE AT RELIEFBLOCK. SENT TO WORK AND ORDER PARTS.JAN 28, 2012 - DAN HEINECHECK UNIT AIR HAD FROZE UP. AIR DRYER HAD BEEN REMOVED, TO LOOK UP PARTS. FINDWHERE OLD WAS PUT AND LOAD UP.26-Jan-2012WOC119211 - INSTALL HUNGRY BOARDS21,368Install Hungry BoardsWork carried out on site at LedcorFabricated by Mckenzie WeldingInstalled by SMS2-Jan-2012WOC114520 - REPAIR DOG BONE21,575repair dog boneJAN 1, 2012 - DAN HEINECHECK OPERATOR COMPLAINT OF LOOSE BOLT. BOLT HAD BROKEN ON DOG BONE. PIN WASWALKING OUT. KNOCK PIN BACK IN. LOOK UP PARTS.JAN 2, 2012 - DAN HEINEDRIVE TO FINNING AND PICK UP PARTS. DRIVE TO SIRE, PULL PERMIT. GET TO UNIT AND PULLBROKEN BOLT. CUT END TO GET IT OFF. INSTALL NEW BOLT AND WASHERS. TORQUE TO 230LB/FT. CANT CHECK FOR PLAY AS NO ONE IN AREA. START UNIT (HAD TO BOOST) AND WARM UP.CALL UP.JAN 3, 2012 - DAN HEINESTART UNBIT, CHECK DOG BONE WHEN SOMEONE SHOES UP. THERE IS A BIT O FPLAY ON BOTHSIDES OF DOG BONE.25-Nov-2011WOC109252 - BRASS IN TORQUE SCREENEmeco Canada Limited GST Registration # 104545959RTweb www.emecogroup.com21,242Page 13 of 31Printed on: 12-Jan-2016

Maintenance History Continued for Equipment ID: RDC044Start DateJob Number / DescriptionMeter Reading (Hrs)brass in torque screenNOV 25, 2011 - BRASS IN TORQUE FILTER/SCREENNOV 25, 2011 - DAN HEINEDRIVE TO SITE. TALK WITH CUSTOMER ABOUT FINDINGS AND GET PIECES. CHECK UNIT WORKING.START RAN UP AND DO STILL TEST AND CHECK OUTLET RELIEF. STALLS AT 1600-1605 AND OUTLETRELIEF ID 72 PSI. BOTH ASKED SHUT UNIT DOWN TO GET READY TO DUMP OIL.NOV 26, 2011 - DAN HEINEDRIVE TO SITE/ WAIT FOR ESCORT. SIGN IN AND GO TO UNIT. GET OIL TUBE AND DRAINTORQUW CONVERTER AND HYD TANK. PULL SCREEN ON TORQUE. BUNCH OF METAL AND BRASS ONBOTTOM. PULL TORQUE SCAVENGE PUMP. DIASSEMBLED AND CHECK GEAR AND BUCHINGS. ALOK. PULL HYD AND PARK BRAKE FILTERS. FINE FILINGS ON P/B. HOLE IN MAIN FILTER HOUSINGWHERE SOS PART IS FILL OF METAL. CLEAN OUT. REPLACE BOTH FILTERS. CHECK INLET ANDOUTLET OF HOIST PUMP. BOTH LOOK OK. PULL COVER OFF HYD TANK, MOP UP OIL THAT CAN'TDRAIN. SOME PRETTY BIG FLAKES OF METAL ON BOTTOM AND A FEW CHUNKS OF FIBRE DISCMATERIAL. INSTALL NEW GASKET AND PUT COVER BACK ON. PULL SCREEN OUT OF COOLER FORBIT OF METAL AND SMALL FIBRE CHUNKS. CLEAN AND PUT BACK. CLEAN UP WORK AREA. DRIVEBACK TO SHOP.NOV 27, 2011 - DAN HEINEDRIVE TO SITE, WAIT FOR ESCORT. SIGN IN. GET HYD OIL IN TRUCK TOPPED UP AFTER DRYSTARTING. CHECK ALL LOCK UP PRESSURE ALL OK. GO FOR TEST RUN. HAUL 4 LOADS 13 RINGBACK TO YARD. TRUCK PULLED GOOD, BUT HAD A BIT OF VIBRATION, ESPECIALLY WHEN DUMPING.DROP TORQUE OIL TO CHECK SCREEN. WAS PRETTY CLEAN TWO SMALL SLIVERS OF BRASS.NOTHING IN COOLER SCREEN. CHECK DRIVELINE FIND FRONT U-JOINT IS TOAST, CAUSING THECONTAMINATION IN TORQUE. ORDER U-JOINT AND ADVISE ON FINDINGS. WAIT TO BEAR IFTORQUE IS TO BE CHANGED.DEC 3, 2011 - KARL LTRAVELLED TO SITE, WAIT FOR ESCORT, SIGN IN, MACHINE IN LAYDOWN. DRAINED HYDRAULICTANK AND TORQUE, REMOVE AND COVER HYDRAULIC LINES. REMOVE DRIVELINE, REMOVE TORQUECONVERTER FROM ENGINE, DROP ON GROUND HOIST OUT FROM UNDER TRUCK, PACK UP TRUCK,STRAP DOWN TORQUE IN BACK OF TRUCK. WAIT FOR ESCORT, TRAVEL BACK TO SHOP. INLOADEDTORQUE IN SHOP AND STARTED TO DIASSEBMLE.DEC 4, 2011 - KARL LDISASSEMBLE AND REASSEMBLE. HAD TO FABRICATE LONGER PUSH BOLTS TO DISASSEMBLE ALSOMODIFY PULLER TO REMOVE RAIL.Dec 5, 2011 - TOM B/KARL LFINISH ASSEMBLY OF TORQUE CONVERTER, LOADED INTO TRUCK. TRAVEL TO SITE. INSTALLEDTORQUE, NEW U-JOINTS IN DRIVELINE. FILLED TANK, DID N START CRANK OVER, FILLED TANK,RAN ON IDLE 10 MIN. SUCTION HOSE LEAKING, TIGHTEN CLAMP, CLAMP BROKE, HAD TO FINDANOTHER ONE. INSTALLED CLAMP. TOOK FOR TEST DRIVE AROUND YARD, TORQUE STALL 1600RPM. ALSO REPAIR WIRING FOR LOCK UP SOLENOID, INSTALL NEW CONNECTOR.4-Nov-2011WOC106529 - LRI TIRE20,815GOT A CALL FROM GLEN 370 9533 A

Negotiated sales for heavy equipment & industrial assets 2005 Caterpillar 777D Year 2005 Manufacturer Caterpillar Model 777D Asset Type Rock Truck Serial Number CAT0777DCAGC01618 Usage 26,069 hrs Comes with retarder, A/C, liner, heated box, auto lube, 27.00R49 Notes fast fuel, Lincoln