Transcription
EZ Lynk Installation
ATTENTION!68RFE Relearn ProcessIf your 2010 Ram is equipped with the 68RFE automatictransmission, you must perform a re-learn procedure each timethe ECM is flashed, even if you aren’t loading transmissiontuning. Failure to do so will cause premature transmissionfailure. To perform the procedure after the ECM is flashed, drivethe truck and apply no more than 30% throttle for at least 2530 miles. It is important that the transmission shifts up anddown as much as possible during this period. NOTE: The 25-30miles is to re-establish the CVI values. It is common for thesetransmissions to take 400-500 miles or more to settledown. Sustained highway speeds should be avoided for the first25-30 miles. If you purchased a tuned TCM for your 2007.52009 68RFE equipped Ram, you must perform the same relearnprocess upon installation of the TCM.
Technical SupportFor technical support or assistance with installation, please contact us 015 M-F 9AM-5PM CSTCustomer ServiceFor general questions and information, please contact us 015 M-F 9AM-5PM CSTCTTTuning.ca
Step 1 – Turn ignition the RUN position and plug in the Auto Agent to theOBD-II port. Once plugged in, you should see a blue light on the AutoAgent’s OBD plug. If the light is on, the Auto Agent is emitting wi-fi.Step 2 - On your smart phone or table, open your wi-fi settings and selectthe EZ Lynk wi-fi. It’s normal for it to read No Internet Connection onceconnected to the wi-fi.Step 3 – Once connected to the EZ Lynk wi-fi, open the Auto Agent app.The gauges screen should appear.
Step 4 – Click the menu button in the top right corner and select Vehicles.Step 5 – Select Technicians.
Step 6 – If the Auto Agent is not linked, select the plus sign.Step 7 – Type in [email protected] and click Next.
Step 8 – Type in your vehicle details and click Done.Step 9 – Vehicle is now linked.
Step 10 – Go back to the Vehicle menu and click ECU Profiles. If youpurchased tuning and receive this message, contact us with your ordernumber.Step 11 – Once you have your files, you will see the files that are availableto download.
Step 12- Click the cloud icon on the desired tune. Within a few seconds, thecloud icon will turn into an Install icon. Click install.Step 13 – For Cummins only, locate the diagnostic port behind the intakemanifold. If installing on a Titan XD, proceed to Step 15. For all others,proceed to Step 16.
Supplied unlock cable plugged into the diagnostic port.Step 14 – Plug the other end of the unlock cable to the corresponding porton the Auto Agent. Your screen may look different if using an AutoAgent 2.0.
Step 15 – If you have a Titan XD, you will take the same supplied unlockcable, and plug it into the Titan specific cable (purchased separately) toessentially make one long cable. One end plugs into the Auto Agent, theother plugs into the triangle shaped data link near the firewall on thepassenger side. Remove the protective cap and plug in the cable.Supplied unlock cable and Titan specific cable plugged into each other asshown below.Plug in the Titan specific cable to the data link as shown below.
Step 16 – Turn ignition off. Click Next.Step 17 – Turn ignition to the RUN position. Click Next.
Step 18 – The Auto Agent will now begin to flash the ECM. For Cummins, itis normal for the progress to stay and 1% and 2% a little longer thanusual.Step 19 – When prompted to do so, turn the ignition off. Click Next.
Step 20 – Turn ignition to the RUN position. Click Next.Step 21 – Click Let’s go! You are now ready to start the truck. If your truckis equipped with a 68RFE transmission, you MUST perform the relearnprocedure as described in the beginning of this manual.
Cummins SOTF Switch Install1. Disconnect negative battery terminals.2. Route the switch wires through the firewall and locate the crankcasepressure sensor. On the 6.7L Cummins, it’s located on the top driver’sside of the valve cover underneath the wiper cowl. On the 5.0LCummins, it’s located below the oil fill cap.3. Insert the switch wires into the supplied connector following the colorcoded markings. The red wire inserts at the red marked slot, the blackwire inserts at the black marked slot, and the white wire inserts intothe remaining unmarked slot. You’ll hear a click when they’re seatedinto the connector. Tug on the wires to ensure the wires are properlyseated.4. Plug the switch connector into the crankcase pressure sensor’s wiringharness.5. Mount the switch in your desired location.6. Reattach the negative battery terminals and drive the vehicle to confirmproper switch function after the SOTF tune is installed and thetransmission relearn procedure (if applicable) is complete.
LML Duramax SOTF Switch Install1. Disconnect the negative battery terminals.2. Route the switch wires through the firewall and locate the ECM. The ECM islocated on the front driver’s side of the engine compartment next to thedriver’s side battery.3. The ECM has 3 connectors. One is blue, one is black, and one is grey.Carefully unplug the GREY connector.4. With the connector in your hand, remove the zip tie holding the protectivecap and remove the cap.5. With an o-ring pick or similar, carefully remove the grey cap on the pinside to expose the pins in the connector.6. 2011 year models will have a yellow wire in pin slot #11. Using a pinremoval tool, remove the yellow wire and secure to the harness usingelectrical tape. 2012-2016 year models will have a plastic filler pin ratherthan a wire. Using a small tool such as a drill bit, press the filler pin outof the connector.7. Insert the yellow wire in pin slot #11. Once inserted and seated, tug onthe wire to ensure it is secure. Insert the black wire in pin slot #35 andconfirm it is secured in the connector.8. Reassemble the connector in reverse order. Install the switch in yourdesired location.9. Reattach the negative battery terminals and drive the vehicle to confirmproper switch function after the SOTF tune is installed and the transmissionrelearn procedure (if applicable) is complete.
6.7L PowerStroke SOTF Switch Install1. Disconnect the negative battery terminals.2. Route switch wires through the firewall and locate the fuel temperaturesensor near the fuel filter housing. Unplug the factory harness from thesensor.3. Using the supplied taps, tap the switch wires into the green and greenwith white tracer. Polarity does not matter.4. Mount the switch in your desired location.5. Reattach the negative battery terminals and drive the vehicle to confirmproper switch function after the SOTF tune is installed and thetransmission relearn procedure (if applicable) is complete.
68RFE Relearn Process If your 2010 Ram is equipped with the 68RFE automatic transmission, you must perform a re-learn procedure each time the ECM is flashed, even if you aren’t loading transmission tuning. Failure to do so will cause premature transmission failure.
