Transcription

USER'SMANUALFA162C Security SystemN7527-1V2 Rev B 4/99

–2 –

TABLE OF CONTENTSSYSTEM OVERVIEW . 4General . 4A Partitioned System . 4Zones . 4Burglary Protection . 5Security Codes . 5Fire Protection . 6Alarms . 6Memory of Alarm . 6Phone Access & Voice Response . 6ENTRY/EXIT DELAYS . 7General Information . 7Exit Alarms . 8COMMON ZONE OPERATION . 8ABOUT THE KEYPADS . 9FUNCTIONS OF THE KEYPADS . 12CHECKING FOR OPEN ZONES . 14ARMING PERIMETER ONLY (STAY) . 15ARMING PERIMETER ONLY (INSTANT) . 16ARMING ALL PROTECTION (AWAY) . 172-Partition Away Arming . 17ARMING ALL PROTECTION (MAXIMUM) . 19DISARMING AND SILENCING ALARMS . 20Memory of Alarm . 20BYPASSING PROTECTION ZONES . 21Quick Bypass . 22Displaying Bypassed Zones . 22CHIME MODE . 23PANIC KEYS . 24USING DEVICE COMMANDS . 25PAGING FEATURE . 27SECURITY CODES . 27General . 27Babysitter Code . 27Duress Code . 27Quick Arming . 27To Add or Change A User . 28To Delete A User . 28TESTING THE SYSTEM . 29TROUBLE CONDITIONS . 31FIRE ALARM SYSTEM . 33NFPA RECOMMENDATIONS . 34EMERGENCY EVACUATION . 35MAINTAINING YOUR SYSTEM . 36QUICK GUIDE TO SYSTEM FUNCTIONS . 38SUMMARY OF AUDIBLE NOTIFICATIONS . 40GLOSSARY . 41INSURANCE CREDIT REQUEST FORM . 47–3 –

SYSTEM OVERVIEWGeneralCongratulations on your ownership of a First Alert Professional Partitioned Security System.You've made a wise decision in choosing it, for it represents the latest in security protectiontechnology today.This system offers you three forms of protection: burglary, fire and emergency. Your systemconsists of at least one keypad which provides control of system operation, and includesvarious sensors which provide perimeter and interior burglary protection, plus smoke orcombustion detectors designed to provide early warning in case of fire.The system uses microcomputer technology to monitor all protection zones and system statusand provides appropriate information for display on the keypad(s) used with the system, andinitiates appropriate alarms. Your system may also have been programmed to automaticallytransmit alarm or status messages over the phone lines to a central alarm monitoring station.A Partitioned SystemSimply stated, a partitioned system is a single physical alarm system that provides twoindependent areas of protection intended for use by separate users. For the most part, youneed not know about other users and their structure in the system. However, when the systemis set up for 2-partition operation, you may see display messages from time to time whichindicate that the system is in use by another user; this is normal. A partitioned system mayalso have a "common zone" area, which is an area shared by users of both partitions.Refer to the COMMON ZONE OPERATION section for details on using this feature.ZonesYour system's sensing devices have been assigned to various "zones." For example, thesensing device on your Entry/Exit door may have been assigned to zone 01, sensing deviceson windows in the master bedroom to zone 02, and so on. These numbers will appear on thedisplay, along with a description for that zone (on Alpha display keypads only, if programmed)when an alarm or trouble condition occurs.–4 –

SYSTEM OVERVIEWBurglary ProtectionYour system provides four modes of burglary protection: STAY, AWAY, INSTANT andMAXIMUM, and allows you to BYPASS selected zones while leaving the rest of the systemarmed. You must turn on or "arm" the burglary protection portion of your system before it willsense burglary alarms. The system also provides a CHIME mode, for alerting users to theopening of protected doors and windows while the system is disarmed. Refer to the othersections of this manual for procedures for using these features.The following table lists the four different arming modes and the results of each.ArmingModeAWAYSTAYINSTANTMAXIMUMExit DelayYesYesYesYesFeatures For Each Arming ModeEntry DelayPerimeter ArmedYesYesNoNoYesYesYesYesInterior ArmedYesNoNoYesSecurity CodesAt the time of installation, you were assigned a personal four-digit security code, known only toyou. You must enter the security code when arming and disarming the system, and whenperforming other system functions. As an additional safety feature, other users who do not havea need to know your code can be assigned different security codes. Refer to the SECURITYCODES section for procedures on adding security codes to the system.Fire ProtectionThe fire protection portion of your security system (if used) is always active and will sound analarm if a fire condition is detected. Refer to the FIRE ALARM SYSTEM section for importantinformation concerning fire protection, smoke detectors and planning emergency exit routesfrom the premises.–5 –

SYSTEM OVERVIEWAlarmsWhen an alarm occurs, both the keypad and external sounders sound, and the keypad displaysthe zone(s) causing the alarm. If your system is connected to a central monitoring station, analarm message is also sent. To stop the alarm sounding, simply disarm the system.Memory of AlarmWhen an alarm condition occurs, the keypad displays the number(s) of the zone(s) that causedthe problem, and displays the type of alarm (ex. FIRE, ALARM). It remains displayed until it iscleared by disarming the system (see DISARMING THE SYSTEM section).Phone Access &Voice ResponseCapabilityYour system may include a voice module that will permit you to access the system via a Touchtone phone, either on-premises or by call-in when away. The phone access feature will enableyou to do the following: Receive synthesized voice messages over the telephone regarding the status of the securitysystem. Arm and disarm the system and perform most function commands via the telephone, withvoice confirmation provided after each command entry.Complete information regarding the use of this feature is provided in a separate manual entitledPHONE ACCESS USER'S GUIDE, which accompanies the voice module.Paging FeatureIf the paging feature has been programmed for your system, your pager will respond tocertain conditions as they occur in your system, and display code numbers indicating thetype of condition that has occurred.For detailed information, refer to PAGING FEATURE section later in this manual.–6 –

ENTRY/EXIT DELAYSGeneral InformationExit Delay RestartActive:Your system has preset time delays, known as exit delay and entry delay. Whenever you armyour system, exit delay gives you time to leave through the designated exit door without settingoff an alarm. Exit delay begins immediately after entering any arming command, and applies toall modes of arming protection. Slow “beeps” will sound throughout the exit delay period, ifprogrammed.Restarting Exit Delay While Armed: Your system may have been programmed to allow youto restart the exit delay after the system has been armed in STAY mode. This is useful if youwish to open the entry/exit door to let someone in after arming the system and avoids having todisarm the system and then re-arm it again. If programmed, you can restart the exit delay bypressing the [ ] key. Ask your installer if this feature is active for your system.Entry Delays give you time to disarm the system when you re-enter through the designatedentrance door. But you must disarm the system before the entry delay period ends, or an alarmwill occur. The keypad beeps during the entry delay period, reminding you to disarm thesystem. There are two entry delays (if programmed). The first is for your primary entrance andthe second may be used for a secondary entrance, where a longer delay is required to walk tothe keypad to disarm the system.You can also arm the system with no entry delay at all by using either INSTANT or MAXIMUMarming modes. These modes provide greater security while on the premises or while away forextended periods of time.See your installer for your delay times.Partition 1Partition 2Exit Delay:Exit Delay:secondsseconds–7 –Entry Delay 1:secondsEntry Delay 2:secondsEntry Delay 1:secondsEntry Delay 2:seconds

ENTRY/EXIT DELAYSExit AlarmsTo minimize false alarmssent to the alarmmonitoring company,your system may havebeen programmed for thisfeature. Ask your installerif "Exit Alarm" is active foryour system.Exit Alarm ActiveWhenever you arm the system, the exit delay begins. If an entry/exit door or interior zone isfaulted when the exit delay ends (e.g., exit door left open), the system sounds an alarm andstarts the entry delay timer. If you disarm the system before the entry delay ends, the alarmsound stops and the message "CANCEL ALARM" or "CA" is displayed on the keypad, alongwith a zone number indicating the faulted zone. No message is sent to the alarm monitoringcompany. To clear the exit alarm condition, the open zone must be made intact; to clear thedisplay, enter your code plus OFF.If you do not disarm the system before the entry delay ends, and an entry/exit door or interiorzone is still open, the alarm sound continues and an "exit alarm" message is sent to the alarmmonitoring company. The message ""EXIT ALARM" or "EA" is displayed on the keypad, alongwith a zone number indicating the faulted zone. To stop the alarm, the system must bedisarmed (your code plus OFF); to clear the display, enter your code plus OFF a second time.An “exit alarm” also results if an entry/exit door or interior zone is faulted within two minutesafter the end of the exit delay.COMMON ZONE OPERATIONAsk yourinstaller if a commonzone was assigned.Your system may have been set up to use a common zone, which is an area shared by users ofboth partitions, such as a foyer or lobby. If so, please note the following: The common zone will sound and report alarms only when both partitions are armed. If onlyone partition is armed, the system ignores faults on the common zone. Either partition may arm its system if the common zone is faulted, but once armed, the otherpartition will not be able to arm unless the common zone is first bypassed or the fault iscorrected. If either partition is armed and the other is in chime mode, the common zone will not chime.The common zone will chime if both partitions are disarmed and either is in chime mode. Faults on the common zone are displayed on keypads in both partitions. Either partition can clear and restore the common zone after an alarm.–8 –

ABOUT THE KEYPADSGeneral Your keypads allow you to control all system functions. The keypads feature a telephonestyle (digital) keypad and a Liquid Crystal Display (LCD) which shows the nature and locationof all occurrences.The keypads also feature a built-in sounder which will sound during alarms and troubles. Thekeypads also "beep" during certain system functions, such as during entry/exit delay times, inCHIME mode, and when depressing any of the keys (to acknowledge the key press).There are two basic types of keypads – a Fixed-Word keypad and an Alpha key-pad (bothdescribed below). Fixed-Word and Alpha keypads are functionally the same, even thoughthey have different types of displays.2-Line Alpha Keypad2-line Alpha keypads feature a 2-line, 32-character alphanumeric LCD which can displaysystem messages in friendly English. These keypads can also be programmed with customzone descriptors. The screen displays depicted throughout this manual are examples ofdisplays that would typically appear on a 2-line Alpha keypad.1-Line Alpha Keypad1-line Alpha keypads feature a 16-character alphanumeric LCD which can display systemmessages in friendly English. Messages are the same as those for 2-line Alpha keypads, butare displayed one line at a time. To view the second line of the message, simply press the# key. To return to the first line, press the # again, or wait 3 seconds.After pressing the#key, wait at least 3 seconds before entering a command.Fixed-Word Keypad Fixed-Word keypads are functionally identical to Alpha keypads, but the LCD display usespre-designated words to identify the nature and location of occurrences.Fixed-Word keypads are available with two styles of displays, “A” or “B” (see page 11),depending on keypad used.–9 –

ABOUT THE KEYPADSAWAYFirst Alert ARMEDABREADYCDAWAYNO ACSTAYCHIMEBATALARM INSTANTCHECK BYPASSNOT READYFIREFirst KP Alpha KeypadsBATARMEDREADYREADY0AWAY1MAXIMUM4*ALARM STAY CHIMEFIRE CHECK INSTANTREADYOFFOFFNO ACBYPASS NOT READYARMEDFirst ME7890#READY*ProfessionalFA210KP Fixed-Word Keypad(single line/2-line)– 10 –FA250KP Fixed-Word Keypad

ABOUT THE KEYPADSFixed-Word Keypad DisplaysAWAYAll burglary zones, interior & perimeter, are armed.STAYPerimeter burglary zones, such as windows and doorsare armed.INSTANTPerimeter burglary zones armed andentrydelay is turned off.BYPASSOne or more burglary protection zones havebeen bypassed.NOT READYAppears when burglary portion of the system is notready for arming (due to one or more open protectionzones).READYThe burglary portion of the system is readyto be armed.NO AC Appears when AC power has been cut off.System is operating on backup battery power.ACAppears when AC power is present.CHIMEBATALARMCHECKFIREALARMCHECKFIRENO ACAWAYCHIMESTAYBATINSTANTBYPASSNOT READYSTYLE A KEYPAD DISPLAYAWAYNO ACBYPASS NOT READYALARM STAY CHIMEFIRE CHECK INSTANTBATSTYLE B KEYPAD DISPLAYAppears when the CHIME feature is ON.Low battery condition in a wireless sensor (if zone number displayed) or low system battery (if nozone number displayed).Appears when an intrusion has been detected and the system is armed (also appears during afire alarm or audible emergency alarm). Accompanied by the protection zone in alarm.Appears when a malfunction is discovered in the system at any time or if an open is detected ina FIRE zone at any time or a fault in a DAY/NIGHT burglary zone during a disarmed period.Accompanied by a display of zone number in trouble.Appears when a fire alarm is present. Accompanied by a display of the zone in alarm.– 11 –

FUNCTIONS OF THE KEYPADSEE TYPICAL ALPHA KEYPAD ON NEXT PAGE1. DISPLAY WINDOW. Alpha Keypad: A 2-line, 32-characterLiquid Crystal Display (LCD). Displays protection zoneidentification, system status, and messages.Fixed-Word Keypad: Displays protection zone ID and systemstatus messages using pre-designated words.2. OFF KEY: Disarms burglary portion of the sys tem, silencesalarms and audible trouble indicators, and clears visualdisplay after problem's correction.3. AWAY KEY: Arms the entire burglary system, perimeter andinterior.4. STAY KEY: Arms perimeter portion of burglary system only.Interior protection is not armed, which allows movement withinpremises without causing alarm.5. MAXIMUM KEY: Arms in manner similar to AWAY mode, butwithout the entry delay feature, thus providing maximumprotection. An alarm will occur im mediately upon opening anyprotection point, including the main door.6. TEST KEY: Tests the system and alarm sounder if disarmed.Refer to TESTING THE SYSTEM section for test procedures.7. BYPASS KEY: Removes individual protection zones frombeing monitored by the system.8. INSTANT KEY: Arms in manner similar to STAY mode, butwithout the entry delay feature. Entering via the entry/exitdoor will cause an instant alarm.9. CODE KEY: Used to assign additional user codes for otherusers of the system.10. CHIME KEY: Turns CHIME mode on and off. When on, theopening of windows or doors while the system is disarmed willsound 3 beeps at the keypad(s).11. READY KEY: Displays all open protection zones.#KEY: "Quick Arm" key permits ARMING of the systemwithout the use of a security code (if so programmed).13. KEYS 0–9: Used to enter your security code(s). See Note onnext page.12.14. READY INDICATOR: (GREEN) Lit when the system is readyto be armed (no faults present). While the system is disarmed,this indicator will go on and off as protection zones are closedand opened.15. ARMED INDICATOR: (RED) Lit when the system has beenarmed (STAY, AWAY, INSTANT or MAXIMUM).16. INTERNAL SOUNDER: The built-in keypad sounder mimicsthe alarm sounder during alarms, and will also "beep" duringcertain system functions (see SUMMARY OF AUDIBLE/VISUAL NOTIFICATION).17. EMERGENCY (PANIC) KEYS:Individual keys A, B, and C (key D not used).On some keypads, these keys are not present and certain keypairs may be available for emergency functions.For further information, refer to the PANIC KEYS section.– 12 –

FUNCTIONS OF THE KEYPAD1 DISARMED ****READY TO ARM171514IMPORTANT!:When entering codes and commands,sequential key depressions must be madewithin 2 seconds of one another. If 2seconds elapses without a key depression,the entry is aborted and must be repeatedfrom its beginning.2ABREADYCDFirst ECHIME7890#5163ARMED6710READY*9ProfessionalSHOWN WITHFLIP-DOWNKEY COVERREMOVED8111312TYPICAL ALPHA KEYPADFixed-Word Keypads are functionally similar,except for screen displays (see page 10).– 13 –

CHECKING FOR OPEN ZONESUsing the READY KeyBefore arming your system, all protected doors, windows and other protection zones must beclosed or bypassed (see BYPASSING section). Otherwise the keypad will display a "NotReady" message. Using the READY key will display all zones that are faulted, making it easierfor you to secure any open zones.To show faulted zones:DISARMED - PRESS TO SHOW FAULTSREADY1. Note: Keypads light a green READY indicator when systemis ready. If not lit, the system is not ready to be armed.PRESS THE READY KEYDo not enter the security code, but simply press the READYkey.2.F AULT 05 F RONTUPST AIRS BE DROOMSECURE FAULTED ZONESTypical fault display shows open zones. Secure or bypassthe zones displayed before arming the system.3.* * * DISARME D * * *RE ADY T O ARMSYSTEM CAN BE ARMEDThe "Ready" message will be displayed when all protectionzones have been either closed or bypassed.You may now arm the system as usual.– 14 –

ARMING PERIMETER ONLY(With Entry Delay ON)Using the 3STAY keyUse this key when you are staying home, but might expect someone to use the entrance doorlater.When armed in STAY mode, the system will sound an alarm if a protected door or window isopened, but you may otherwise move freely throughout the premises. Late arrivals can enterthrough the entrance door without causing an alarm, but they must disarm the system within theentry delay period or an alarm will occur.Close all protected perimeter windows and doors before arming (see CHECKING FOROPEN ZONES section). The green READY indicator on the keypad should be lit if the systemis ready to be armed.STAY1. (Security Code)2.ARME D *** S T AY ***NOTE:3ENTER SECURITY CODE THEN PRESS STAYExample: 7296 then press the STAY key.LISTEN FOR 3 BEEPSThe keypad will beep three times and will display the armedSTAY message. The red ARMED indicator also lights.If you wish to open the entry/exit door to let someone in after arming STAY, you canre-start the exit delay at any time (if programmed) – simply press the [ ] key, andthen let that person in. This will avoid having to disarm the system and then re-arm itagain.– 15 –

ARMING PERIMETER ONLY(With Entry Delay OFF)7Using theINSTANT KeyUse this key when you are staying home and do not expect anyone to use the entrance door.When armed in INSTANT mode, the system will sound an alarm if a protected door or windowis opened, but you may otherwise move freely throughout the premises. The alarm will alsosound immediately if anyone opens the entrance door.Close all protected perimeter windows and doors before arming (see CHECKING FOROPEN ZONES section). The green READY indicator on the keypad should be lit if the systemis ready to be armed.INSTANT1. (Security Code)2.ARME D * INST ANT *NOTE:7ENTER SECURITY CODE THEN PRESS INSTANTExample: 7296 then press the INSTANT key.LISTEN FOR 3 BEEPSThe keypad will beep three times and will display the armedINSTANT message. The red ARMED indicator also lights.If you wish to open the entry/exit door to let someone in after arming STAY, you canre-start the exit delay at any time (if programmed) – simply press the [ ] key, andthen let that person in. This will avoid having to disarm the system and then re-arm itagain.– 16 –

ARMING ALL PROTECTION(With Entry Delay ON)2Using theAWAY KeyUse this key when no one will be staying on the premises.When armed in AWAY mode, the system will sound an alarm if a protected door or window isopened, or if any movement is detected inside the premises. You may leave through theentrance door during the exit delay period without causing an alarm. You may also re-enterthrough the entrance door, but must disarm the system within the entry delay period or an alarmwill occur.Close all protected perimeter windows and doors before arming (see CHECKING FOROPEN ZONES section). The green READY indicator on the keypad should be lit if the system isready to be armed.AWAY 1.2(Security Code)2.ARME D ** AWAY **YOU MAY E XIT NOWThe "You May Exit Now"portion of the messagedisappears when the exitdelay expires.2-Partition AWAYArmingENTER SECURITY CODE THEN PRESS AWAYExample: 7296 then press the AWAY key.LISTENThe keypad will beep twice, or beep continuously if an exitwarning has been programmed for your system, anddisplays the armed AWAY message. The red ARMEDindicator also lights.In a two-partition system, you can arm both partitions in the AWAY mode at the same time if thesame master code is assigned to both partitions. You can do this from either partition's keypad.This procedure is not applicable to disarming or any other system function.(Continued)– 17 –

ARMING ALL PROTECTION(With Entry Delay ON)2-Partition AWAYArming(Continued)To arm both partitions, first make sure both partitions are READY TO ARM.AWAY1. 2(Master Code)2.AWAY 2ENTER MASTER CODE THEN PRESS AWAYTWICEExample: 7 2 9 6 and press the AWAY key, thenpress the AWAY key again.The first press of AWAY arms the local partition, thesecond press of AWAY arms the other (remote) partition.The “Armed Away” display should appear, and remaindisplayed (with exit warning beeps, if programmed)throughout the exit delay period if both partitions weresuccessfully armed AWAY. The red ARMED indicatorshould also light.If the “READY TO ARM” message re-appears when thesecond AWAY key press is made, both partitions havefailed to arm due to an open zone in the remote partition.If the remote partition is not ready to arm, neitherpartition will arm when using this particularprocedure .ARME D ** AWAY **YOU MAY E XIT NOWThe "You May Exit Now"portion of the messagedisappears when the exitdelay expires.– 18 –

ARMING ALL PROTECTION(With Entry Delay OFF)4Using theMAXIMUM KeyUse this key when the premises will be vacant for extended periods of time such as vacations,etc., or when no one will be moving through protected interior areas.When armed in MAXIMUM mode, the system will sound an alarm if a protected door or windowis opened, or if any movement is detected inside the premises. You may leave through theentrance door during the exit delay period without causing an alarm, but an alarm will besounded as soon as someone re-enters.Close all protected perimeter windows and doors before arming (see CHECKING FOROPEN ZONES section). The green READY indicator on the keypad should be lit if the system isready to be armed.MAXIMUM1. 4(Security Code)2.ARME D * MAXIMUM *YOU MAY E XIT NOWThe "You May Exit Now"portion of the messagedisappears when the exitdelay expires.ENTER SECURITY CODE THEN PRESS MAXIMUMExample: 7296 then press the MAXIMUM key.LISTENThe keypad will beep twice, or beep continuously if exitwarning has been programmed for your system, and willdisplay the armed MAXIMUM message (AWAY/INSTANT onfixed-word keypads). The red ARMED indicator also lights.– 19 –

DISARMING AND SILENCING ALARMS1Using theOFF KeyUse the OFF key to disarm the system and to silence alarm and trouble sounds. See"SUMMARY OF AUDIBLE NOTIFICATIONS" section for information which will help you todistinguish between FIRE and BURGLARY alarm sounds.IMPORTANT: If you return and the main burglary sounder is on, DO NOT enter the premises,but call the police from a nearby safe location. If you return after an alarm has occurred andthe main sounder has shut itself off, the keypad will beep rapidly upon entering, indicating thatan alarm has occurred during your absence and an intruder may still be on the premises.LEAVE IMMEDIATELY and CONTACT THE POLICE from a nearby safe location.To disarm the system and silence burglary alarms:OFF1. (Security Code)2.Memory of Alarm* * * DISARME D * * *RE ADY T O ARM1ENTER SECURITY CODE, THEN PRESS OFFExample: 7296 then press the OFF key.LISTEN FOR 1 BEEPThe “Ready” message will be displayed (if no alarms haveoccurred while armed) and the keypad will beep once toconfirm that the system is disarmed.If an alarm occurs, the keypad displays the zone number (s) that caused the alarm and the typeof alarm. These messages remain displayed until cleared by a user. To clear the display, notethe zone number displayed and repeat step 1 above. If the “Ready“ message will not display,go to the displayed zone and correct the fault (close windows, etc.). If the fault cannot becorrected, notify your alarm company.– 20 –

BYPASSING PROTECTION ZONESUsing the 6BYPASS KeyThis key is used when you want to arm your system with one or more zones intentionallyunprotected. Bypassed zones are unprotected and will not cause an alarm when violated whileyour system is armed. All bypasses are removed when an OFF sequence (security codeplus OFF) is performed. Bypasses are also removed if the arming procedure that follows thebypass command is not successful.The system will not allow fire zones to be bypassed.To bypass zones, the system must be disarmed first.BYPASS1. 6(Security Code)2.(Zone Numbers)3.BYPASS 07 F RONTUPST AIRS BE DROOMTypical bypass message4.DISARME D BYPASSRE ADY T O ARMENTER SECURITY CODE THEN PRESS BYPASSExample: 7296 then press the BYPASS key.ENTER ZONE NUMBERSEnter the zone number(s) for the zones to be bypassed(e.g., 01, 02, 03, etc.).Important! All single-digit numbers must be preceded by azero (for example, enter 01 for zone 1).WAITThe keypad will display the word BYPASS along with eachbypassed zone number. Wait for these zones to bedisplayed, to be sure that intended zones are bypassed.ARM AS USUALArm the system as usual when the keypad displays the"Ready ” message.(Continued)– 21 –

BYPASSING PROTECTION ZONES (Continued)Quick BypassYour system may allow you to easily bypass all open (faulted) zones without having to enterzone numbers individually. Ask your installer if this feature is active.All open (faulted) zonesAll open zones, plus these zones as checked: 173031BYPASS1.2. 6(Security Code)Example: 7BYPASS 07 F RONTUPST AIRS BE DROOMWAIT. In a few moments, all open zones will be displayedalong with the word BYPASS. Wait for these zones to bedisplayed before arming. Arming the system before zonesare displayed eliminates all bypasses.Typical bypass message3.Displaying BypassedZonesENTER SECURITY CODE THEN PRESS BYPASS296 then press the BYPASS key.ARM AS USUAL. Arm the system as usual when thekeypad displays the "Ready" message.DISARME D BYPASSRE ADY T O ARMPreviously bypassed zones can be displayed only when the system is disarmed, and when the“Bypass” message shown in step 3

General Congratulations on your ownership of a First Alert Professional Partitioned Security System. You've made a wise decision in choosing it, for it represents the latest in security protection technology today. This system offers you three forms of protection: b