Transcription
Site Master S331D/S332DCable and Antenna AnalyzerSite Master is the preferred cable and antenna analyzer ofwireless providers, contractors and installers.Color display option shownProgramming ManualS331D Site MasterSiteMasterMS2712SiteMasterMS2711D Spectrum MasterMS2712SpectrumMasterSpectrumMasterMT8212A Cell MasterMS2712CellMasterCellMaster
WARRANTYThe Anritsu product(s) listed on the title page is (are) warranted against defects in materials and workmanship for one year from the date of shipment.Anritsu’s obligation covers repairing or replacing products which prove to be defectiveduring the warranty period. Buyers shall prepay transportation charges for equipment returned to Anritsu for warranty repairs. Obligation is limited to the original purchaser.Anritsu is not liable for consequential damages.LIMITATION OF WARRANTYThe foregoing warranty does not apply to Anritsu connectors that have failed due to normal wear. Also, the warranty does not apply to defects resulting from improper or inadequate maintenance by the Buyer, unauthorized modification or misuse, or operationoutside the environmental specifications of the product. No other warranty is expressed orimplied, and the remedies provided herein are the Buyer’s sole and exclusive remedies.TRADEMARK ACKNOWLEDGEMENTSSite Master is a trademark of Anritsu Company.NOTICEAnritsu Company has prepared this manual for use by Anritsu Company personnel andcustomers as a guide for the proper installation, operation, and maintenance of AnritsuCompany equipment and computer programs. The drawings, specifications, and information contained herein are the property of Anritsu Company, and any unauthorized use ordisclosure of these drawings, specifications, and information is prohibited; they shall notbe reproduced, copied, or used in whole or in part as the basis for manufacture or sale ofthe equipment or software programs without the prior written consent of Anritsu Company.UPDATESUpdates to this manual, if any, may be downloaded from the Anritsu internet site at:http://www.us.anritsu.com.March 2004Copyright ã 2003-2004 Anritsu Co.10580-00100Revision: B
Table of ContentsProgramming Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Control Byte Summary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Control Byte Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Setup System – Control Byte #1 (01h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Set Site Master VNA Frequency – Control Byte #2 (02h) . . . . . . . . . . . . . . . . . . . . . . . . . . 7Select Measurement Mode – Control Byte #3 (03h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Set Site Master VNA Scale – Control Byte #4 (04h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Set Site Master VNA Marker – Control Byte #5 (05h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Set Site Master VNA Single Limit – Control Byte #6 (06h) . . . . . . . . . . . . . . . . . . . . . . . . . 9Set DTF Parameter – Control Byte #7 (07h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Set Time/Date – Control Byte #8 (08h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Set Reference Number – Control Byte #9 (09h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Serial Port Echo On/Off – Control Byte #10 (0Ah) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Site Master VNA Single Sweep Mode On/Off – Control Byte #11 (0Bh) . . . . . . . . . . . . . . . . . 12Watch-Dog Timer On/Off – Control Byte #12 (0Ch) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Sequence Site Master Calibration – Control Byte #13 (0Dh) . . . . . . . . . . . . . . . . . . . . . . . . 13Set Site Master Data Points – Control Byte #14 (0Eh) . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Set Site Master Calibration Mode – Control Byte #15 (0Fh) . . . . . . . . . . . . . . . . . . . . . . . . 13Store Sweep Trace – Control Byte #16 (10h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Recall Sweep Trace – Control Byte #17 (11h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Save System Setup – Control Byte #18 (12h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Recall System Setup – Control Byte #19 (13h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21Query System Status – Control Byte #20 (14h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21Trigger Self-Test – Control Byte #21 (15h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28Read Fail Counter – Control Byte #22 (16h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29Query Trace Names – Control Byte #24 (18h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29Delete Sweep Trace – Control Byte #25 (19h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29Upload SPA Sweep Trace – Control Byte #26 (1Ah) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Query Sweep Memory – Control Byte #27 (1Bh). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33Upload Site Master VNA Sweep Trace – Control Byte #28 (1Ch) . . . . . . . . . . . . . . . . . . . . . 33Query System Status – Control Byte #29 (1Dh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36Select Printer Type – Control Byte #30 (1Eh). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48Select DTF Windowing – Control Byte #31 (1Fh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49Set Site Master VNA Trace Math – Control Byte #32 (20h) . . . . . . . . . . . . . . . . . . . . . . . . 49Recall Sweep Trace – Control Byte #33 (21h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49Set Site Master VNA Trace Overlay – Control Byte #34 (22h) . . . . . . . . . . . . . . . . . . . . . . 61Set SPA A/B Trace – Control Byte #35 (23h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61Site Master PMi
Upload Sweep Trace – Control Byte #36 (24h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62Get Options – Control Byte #37 (25h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71Query Power Level – Control Byte #39 (27h) (Option 29 only) . . . . . . . . . . . . . . . . . . . . . . 72Set Power Meter Units – Control Byte #40 (28h) (Option 29 only) . . . . . . . . . . . . . . . . . . . . 72Power Meter Relative Mode On/Off – Control Byte #41 (29h) (Option 29 only) . . . . . . . . . . . . . 73Power Meter Offset Mode On/Off – Control Byte #42 (2Ah) (Option 29 only) . . . . . . . . . . . . . . 73Power Meter Zero Mode On/Off – Control Byte #43 (2Bh) (Option 29 only) . . . . . . . . . . . . . . . 73Power Meter RMS Averaging On/Off – Control Byte #44 (2Ch) (Option 29 only) . . . . . . . . . . . . 73Power Meter Center Freq and Span Setup – Control Byte #45 (2Dh) (Option 29 only) . . . . . . . . . . 74Trigger Sweep – Control Byte #48 (30h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74Trigger Sweep – Control Word (AA30h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74Check Battery Status – Control Byte #50 (32h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74Set SPA Minimum Sweep Time - Control Byte #53 (35h) . . . . . . . . . . . . . . . . . . . . . . . . . 75Set Trigger Position - Control Byte #54 (36h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75Set Video Trigger Level - Control Byte #55 (37h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75Automatically Save Runtime Setup – Control Byte #64 (40h) . . . . . . . . . . . . . . . . . . . . . . . 76Enter Remote Mode – Control Byte #69 (45h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76Enter Remote Mode Immediately – Control Byte #70 (46h) . . . . . . . . . . . . . . . . . . . . . . . . 76Write Custom Cable – Control Byte #80 (50h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77Recall Custom Cable – Control Byte #81 (51h). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77Write Antenna – Control Byte #82 (52h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78Recall Antenna – Control Byte #83 (53h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78Set Field Strength Measurement – Control Byte #84 (54h) . . . . . . . . . . . . . . . . . . . . . . . . . 79Set Channel Power – Control Byte #85 (55h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79Read Channel Power – Control Byte #86 (56h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80Set Adjacent Channel Power Ratio (ACPR) – Control Byte #87 (57h) . . . . . . . . . . . . . . . . . . . 80Read Adjacent Channel Power Ratio (ACPR) – Control Byte #88 (58h). . . . . . . . . . . . . . . . . . 80Read Signal Standard Name – Control Byte #89 (59h) . . . . . . . . . . . . . . . . . . . . . . . . . . . 81Measure OCC BW % of Power – Control Byte #96 (60h) . . . . . . . . . . . . . . . . . . . . . . . . . 81Measure OCC BW dB Down – Control Byte #97 (61h) . . . . . . . . . . . . . . . . . . . . . . . . . . 82Set Bias Tee Function - Control Byte #98 (62h) (Option 10 only) . . . . . . . . . . . . . . . . . . . . . 82Set Spectrum Analyzer Start/Stop Frequency – Control Byte #99 (63h) . . . . . . . . . . . . . . . . . . 83Set Spectrum Analyzer Center Freq./Span – Control Byte #100 (64h) . . . . . . . . . . . . . . . . . . . 83Set Spectrum Analyzer Scale – Control Byte #101 (65h) . . . . . . . . . . . . . . . . . . . . . . . . . . 83Set Spectrum Analyzer Marker – Control Byte #102 (66h) . . . . . . . . . . . . . . . . . . . . . . . . . 84Set Spectrum Analyzer Single Limit – Control Byte #103 (67h) . . . . . . . . . . . . . . . . . . . . . . 84Set Spectrum Analyzer Peak Hold – Control Byte #105 (69h) . . . . . . . . . . . . . . . . . . . . . . . 85Set Spectrum Analyzer Resolution Bandwidth – Control Byte #106 (6Ah) . . . . . . . . . . . . . . . . 85Set Spectrum Analyzer Video Bandwidth – Control Byte #107 (6Bh) . . . . . . . . . . . . . . . . . . . 85Set Spectrum Analyzer Sweep Mode – Control Byte #108 (6Ch) . . . . . . . . . . . . . . . . . . . . . 86iiSite Master PM
Set Spectrum Analyzer Marker to Peak – Control Byte #109 (6Dh) . . . . . . . . . . . . . . . . . . . . 86Set Spectrum Analyzer Marker to Center – Control Byte #110 (6Eh) . . . . . . . . . . . . . . . . . . . 86Set Spectrum Analyzer Attenuation – Control Byte #111 (6Fh) . . . . . . . . . . . . . . . . . . . . . . 87Set Site Master VNA Segmented Limit Lines – Control Byte #112 (70h) . . . . . . . . . . . . . . . . . 87Set Spectrum Analyzer Multiple Limit – Control Byte #113 (71h) . . . . . . . . . . . . . . . . . . . . 88Set Return Spectrum Analyzer Sweep Time – Control Byte #114 (72h) . . . . . . . . . . . . . . . . . . 89Set Reference Level Offset – Control Byte #115 (73h) . . . . . . . . . . . . . . . . . . . . . . . . . . . 89Read Marker Value – Control Byte #117 (75h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90Set Sweep Averaging – Control Byte #118 (76h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90Field InstaCal – Control Byte #120 (78h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90Read InstaCal Module ASCII Serial Number – Control Byte #124 (7Ch) . . . . . . . . . . . . . . . . . 91Set Site Master Marker (Peak/Valley) – Control Byte #129 (81h) . . . . . . . . . . . . . . . . . . . . . 91Set / Reset Spectrum Analyzer External Reference – Control Byte #133 (85h) . . . . . . . . . . . . . . 91Check Spectrum Analyzer External Reference – Control Byte #134 (86h). . . . . . . . . . . . . . . . . 92Set SPA Preamp State (On/Off/Auto) – Control Byte #136 (88h) . . . . . . . . . . . . . . . . . . . . . 92Set Spectrum Analyzer Units – Control Byte #140 (8Ch) . . . . . . . . . . . . . . . . . . . . . . . . . 92Set Spectrum Analyzer Resolution Bandwidth – Control Byte #141 (8Dh) . . . . . . . . . . . . . . . . 93Set Spectrum Analyzer Video Bandwidth – Control Byte #142 (8Eh) . . . . . . . . . . . . . . . . . . . 93Set Spectrum Analyzer Attenuation – Control Byte #143 (8Fh) . . . . . . . . . . . . . . . . . . . . . . 93Set AM/FM Demodulation – Control Byte #145 (91h) . . . . . . . . . . . . . . . . . . . . . . . . . . . 94Set Baud Rate – Control Byte #197 (C5h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95Set Language – Control Byte #198 (C6h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95Query Time – Control Byte #208 (D0h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95Read ASCII Serial Number – Control Byte #225 (E1h) . . . . . . . . . . . . . . . . . . . . . . . . . . 96Exit Remote Mode – Control Byte #255 (FFh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96Set T1 Transmission Level – Control Word (A001h) (Option 50 only) . . . . . . . . . . . . . . . . . . 96Set T1/E1 Clock Source – Control Word (A002h) (Option 50 only) . . . . . . . . . . . . . . . . . . . . 96Set T1/E1 Pattern – Control Word (A003h) (Option 50 only) . . . . . . . . . . . . . . . . . . . . . . . 97Set T1/E1 Error Insert Type/Value – Control Word (A004h) (Option 50 only) . . . . . . . . . . . . . . 97Set T1/E1 Framing Mode – Control Word (A005h) (Option 50 only) . . . . . . . . . . . . . . . . . . . 98Start and Stop T1/E1 Measurement – Control Word (A006h) (Option 50 only) . . . . . . . . . . . . . . 98Insert Error for T1/E1 Measurement – Control Word (A007h) (Option 50 only). . . . . . . . . . . . . . 98Get T1/E1 Pattern – Control Word (A008h) (Option 50 only) . . . . . . . . . . . . . . . . . . . . . . . 98Get T1/E1 Frame Sync Status – Control Word (A009h) (Option 50 only) . . . . . . . . . . . . . . . . . 99Get T1/E1 Pattern Sync Status – Control Word (A00Ah) (Option 50 only) . . . . . . . . . . . . . . . . 99Get T1/E1 Carrier Status – Control Word (A00Bh) (Option 50 only) . . . . . . . . . . . . . . . . . . . 99Get T1/E1 Error Type and Number – Control Word (A00Ch) (Option 50 only) . . . . . . . . . . . . . . 99Set T1/E1 Line Coding Options – Control Word (A00Dh) (Option 50 only) . . . . . . . . . . . . . . . 100Set E1 Impedance Options – Control Word (A00Eh) (Option 50 only) . . . . . . . . . . . . . . . . . . 100Read T1/E1 Volts Peak-to-Peak – Control Word (A00Fh) (Option 50 only) . . . . . . . . . . . . . . . 100Site Master PMiii
Set T1/E1 Receive Input Configuration Options - Control Word (A013h) (Option 50 only) . . . . . . . 101Set T1/E1 Measurement Duration - Control Word (A014h) (Option 50 only) . . . . . . . . . . . . . . 101Set T1/E1 Data Logging - Control Word (A015h) (Option 50 only) . . . . . . . . . . . . . . . . . . . 101Read T1/E1 dBdsx - Control Word (A016h) (Option 50 only) . . . . . . . . . . . . . . . . . . . . . . 102Read T1/E1 Frequency - Control Word (A017h) (Option 50 only) . . . . . . . . . . . . . . . . . . . . 102Read T1/E1 Frequency Cal - Control Word (A018h) (Option 50 only) . . . . . . . . . . . . . . . . . . 102Set T1/E1 Frequency Cal - Control Word (A019h) (Option 50 only) . . . . . . . . . . . . . . . . . . . 102Select SPA/Power Meter Signal Standard - Control Word (A103h). . . . . . . . . . . . . . . . . . . . 103Select SPA/Power Meter Channel - Control Word (A104h). . . . . . . . . . . . . . . . . . . . . . . . 103Read External Module Name – Control Word (A201h) (Option 6 only) . . . . . . . . . . . . . . . . . 103Read External Module Serial Number – Control Word (A202h) (Option 6 only). . . . . . . . . . . . . 104Read External Module Frequency Range – Control Word (A203h) (Option 6 only) . . . . . . . . . . . 104Read Module Fail Counter – Control Word (A204h) (Option 6 only). . . . . . . . . . . . . . . . . . . 104Clear Module Fail Counter – Control Word (A205h) (Option 6 only) . . . . . . . . . . . . . . . . . . 105Remote Self Test - Control Word (AA15h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105Programming Examples. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108Examples in C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108Example in Visual Basic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117Parameter Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119Spectrum Analyzer Signal Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120VNA Signal Standards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123ivSite Master PM
Programming OverviewNOTE: This programming manual is written exclusively for Anritsu Site Master Models S331D andS332D. For information on firmware upgrades, contact your local Anritsu Service Center. Commandslisted in this manual are not all backward-compatible with earlier Anritsu models.General DescriptionThe Site Master must first be set into “remote” mode for communication with a computer. Remote mode differs from normalrepetitive sweep and single-sweep modes. During remote mode, the Site Master suspends normal operations and attends tothe serial port. The front panel display indicates when the Site Master is in remote mode.Once in remote mode, a series of control bytes and associated data are sent to the Site Master to perform various functionsand activities. The serial port supports virtually all features accessible from the keypad with the exception of the printer. Theprinter requires connection to the same 9-pin connector on the Site Master rear panel used for remote communication.To complete the communication session, send the control byte to exit remote mode and the Site Master will resume normaloperations. You may also exit the remote mode by pressing the ESCAPE/CLEAR key on the Site Master front panel.Interface Cable InstallationThe Site Master is a DTE-type serial device. Communication between the Site Master and a PC is accomplished over a nullmodem serial cable provided with the Site Master (Anritsu part number 800-441). Connect the cable to the Serial Interfaceconnector on the Site Master test connector panel and to the appropriate COM port connector on the PC.Serial Communication ParametersThe Site Master begins communication at 9600 bps when first powered on. It uses no parity bits, 8 data bits, and 1 stop bit(N-8-1). No hardware handshaking is used. The Set Baud Rate Control Byte #197 (C5h) serial command can be used tochange the baud rate to 19,200, 38,400, 56,000 or 115,200. An invalid setting returns the rate to 9600.Communications Error CheckingSince there is no hardware handshaking, byte level error handling must be done by the controlling program. Use the expectednumber of response bytes (listed in the control byte description section of this manual) when waiting for feedback from theSite Master. For data streams going to the Site Master, the “watch dog timer” protects against interrupted transmissions byaborting a control byte sequence if the inter-byte time limit is exceeded.Parameter ValidationThe Site Master validates input parameters for each control byte sequence. If the input parameters are out of range or invalid,the Site Master notifies the computer by sending Parameter Error Byte #224 (E0h). The Site Master discards the receiveddata and waits for the next control byte.Entering Remote ModeSend the Enter Remote Mode Byte #69 (45h) to the Site Master to enter remote mode at the end of the current sweep. Sendthe Enter Remote Mode Immediately byte #70 (46h) to enter remote mode in the middle of a sweep.The Site Master serial port buffer is one byte wide. No internal buffer exists, so waiting for the response from the unit is essential. If the Site Master is not in remote mode, sending a second byte overwrites the original byte commanding it to enterremote mode. If control byte #69 is sent, the Site Master will enter remote mode at the end of the current sweep. If controlbyte #70 is sent, the unit will enter remote mode as soon as it receives the byte. This means that data stored for the currentsweep may be incomplete. Once a response string is received from the Site Master, the unit is ready to accept additional control bytes.Site Master PM1
Exiting Remote ModeTo exit remote mode, send the Exit Remote Control byte #255 (FFh) to the Site Master. The Site Master sends a responsebyte of 255 (FFh) then exits remote mode. Remote mode can also be exited by pressing the ESCAPE/CLEAR front panelkey.Remote Mode Changes to Site Master Operating ParametersSystem parameters changed during remote mode remain changed for normal operation after the unit exits remote mode.However, the changes are not automatically written to the non-volatile EEPROM. Turning off the Site Master power erasesthe changed settings.To retain the changes, the setup must be saved to one of the setup memory locations. Use either the run-time setup location 0,(which holds the power-on defaults) or one of the nine other setup locations. Control byte #64 (40h) sets the auto-save flagwhich commands the Site Master to automatically save the changes to the run-time setup location upon exiting remote mode.See the Site Master User’s Guide or information in this manual on control byte #18 (12h) for further details.Write Cycle Limitation of EEPROMThe EEPROM, used to store calibrations, setups and traces has a guaranteed lifetime of at least 100,000 write cycles and anunlimited number of read cycles. The write cycle limitation is for a specific location. For example, setup #1 can be stored100,000 times and setup #2 can be stored 100,000 times, etc. Because of this, the Site Master does not automatically store thechanged system parameters to the EEPROM. Be aware of the EEPROM write cycle limitation when programming the SiteMaster and keep the number of write cycles to a minimum.Documentation ConventionsThroughout this manual, the following conventions will be observed:Numeric RepresentationHexadecimal numbers are represented with the suffix h. For example, the decimal number 255 is represented in hexadecimalas FFh.Binary numbers are represented with the suffix b. For example, the decimal number 2 is represented in binary as 10b.Decimal numbers are represented with the prefix # when referring to a control byte (command byte) and without a prefix orsuffix in all other cases.Bit PositionsWhen enumerating bits in a byte, bit 0 will always be the least significant bit (LSB).Mode ReferencesThe term “VNA” in reference to a command denotes Return Loss, SWR, Cable Loss and DTF modes. The term “SPA” inreference to a command denotes Spectrum Analyzer mode. All other modes are referenced individually.2Site Master PM
Control Byte SummaryControl Byte#NameDescriptionWatchdogTimer1 (01h)Setup SystemSets system status flags and switchesYes2 (02h)Set VNA FrequencySets Site Master VNA frequency rangeYes3 (03h)Select Measurement ModeSets current Site Master measurement modeYes4 (04h)Set VNA ScaleSets Site Master VNA scale valuesYes5 (05h)Set VNA MarkerSets position and on/off status of Site Master markers in VNA modesYes6 (06h)Set VNA Single LimitSets position and on/off status of the Site Master single limit in VNA modesYes7 (07h)Set DTF ParametersSets Distance to Fault parametersYes8 (08h)Set Time/DateSets time and date of the Site MasterYes9 (09h)Set Reference NumberSets reference number (trace name) for a sweep traceYes10 (0Ah)Serial Port Echo On/OffAllows synchronization of Site Master and request from computer for sweep trace Yes11 (0Bh)VNA Single Sweep On/OffEnables or disables single sweep operation in VNA modesYes12 (0Ch)Watch-dog Timer On/OffEnables or disables the watch-dog timer—-13 (0Dh)Sequence SM CalibrationTriggers a calibration stepYes14 (0Eh)Set Site Master Data PointsSets number of measurement data points for Site Master VNA modesYes15 (0Fh)Set SM Calibration ModeSets the Site Master calibration mode to OSL Cal (standard) or FlexCalYes16 (10h)Store Sweep TraceSaves current trace data to EEPROM—-17 (11h)Recall Sweep TraceSite Master sends the sweep data associated with a trace (obsolete)Yes18 (12h)Save System SetupSaves system setup parameters to EEPROMYes19 (13h)Recall System SetupRecalls system setup parameters from EEPROMYes20 (14h)Query System StatusGets the current system settings (obsolete)—-21 (15h)Trigger Self-TestTriggers a self test—-22 (16h)Read Fail CountersReturns the values of the lock-fail and integrator counters—-24 (18h)Query Trace NamesReturns list of all saved traces—-25 (19h)Delete Sweep TraceDeletes single or all stored sweep tracesYes26 (1Ah)Upload SPA Sweep TraceUploads a spectrum analyzer sweep trace to Site Master (obsolete)Yes27 (1Bh)Query Sweep MemoryQueries Site Master for percentage of memory that is available for trace storage—-28 (1Ch)Upload VNA Sweep TraceUploads a Site Master VNA mode sweep trace to the Site Master (obsolete)Yes29 (1Dh)Query System StatusQueries the Site Master for current system settingsYes30 (1Eh)Select Printer TypeSelects printer typeYes31 (1Fh)Select DTF WindowingSelects DTF Windowing MethodsYes32 (20h)Set VNA Trace MathSelects Trace Math operation for VNA modesYes33 (21h)Recall Sweep TraceQueries the Site Master for sweep trace dataYes34 (22h)Set VNA Trace OverlaySets trace overlay operation and trace for VNA modesYes35 (23h)Set SPA A/B TraceDefines traces “A” and “B” for SPA modeYes36 (24h)Upload Sweep TraceUploads a sweep trace to the Site MasterYes37 (25h)Get OptionsReturns an ASCII string listing installed options—-39 (27h)Query Power LevelReturns power level at RF In in Power Meter mode—-40 (28h)Set Power Meter UnitsSets Power Meter displaying unitYes41 (29h)Power Meter Relative ModeEnables or disables Power Meter Relative ModeYesSite Master PM3
Control Byte#4NameWatchdogTimerDescription42 (2Ah)Power Meter Offset ModeEnables or disables Power Meter offsetYes43 (2Bh)Power Meter Zero ModeEnables or disables Power Meter zeroing modeYes44 (2Ch)Power Meter RMSAveraging On/OffSets Power Meter RMS Averaging.Yes45 (2Dh)Power Meter CenterFrequency and SpanSets the center frequency and span frequency for the Power Meter modeYes48 (30h)Trigger SweepStarts the next sweep—-50 (32h)Check Battery StatusReturns smart battery status—-53 (35h)Set SPA Minimum SweepTimeSets the min sweep time for the SPA when the span is 0Yes54 (36h)Set Trigger PositionSets the trigger position for the SPA when the span is 0Yes55 (37h)Set Video Trigger LevelSets the trigger level for the SPA in video trigger modeYes64 (40h)Auto Save Runtime SetupAutomatically save the runtime setup when exiting remote modeYes69 (45h)Enter Remote ModeEnters remote mode at the end of the sweep and returns model number andfirmware version—-70 (46h)Enter Remote ModeImmediatelyEnters remote mode immediately and returns model number and firmwareversion—-80 (50h)Write Custom CableWrites Custom Cable data to Site MasterYes81 (51h)Recall Custom CableRecalls Custom Cable data from Site MasterYes82 (52h)Write AntennaWrites custom antenna data to the Site Master via the serial portYes83 (53h)Recall AntennaRecalls custom antenna data from the Site Master via the serial portYes84 (54h)Set Field StrengthMeasurementSets the field strength measurement state and the antenna indexYes85 (55h)Set Channel PowerSets the Channel Power measurement state and the setup parametersYes86 (56h)Read Channel PowerReads the current channel power or the channel power of a stored traceYes87 (57h)Set ACPRSets the ACPR measurement state and parametersYes88 (58h)Read ACPRReads the current adjacent channel power or the adjacent channel power of astored traceYes89 (59h)Read Signal StandardNameReturns the signal standard name in EnglishYes96 (60h)Measure OCC BW % ofPowerMeasures OCC BW with % of Power methodYes97 (61h)Measure OCC BW dBDownMeasures OCC BW with dB down methodYes98 (62h)Set Bias Tee FunctionSet the Bias Tee function On/Off (Option 10 only)Yes99 (63h)Set Spectrum AnalyzerStart/Stop FrequencySets the Spectrum Analyzer Start and Stop frequenciesYes100 (64h)Set Spectrum AnalyzerCenter Freq./SpanSets the Spectrum Analyzer center frequency and frequency spanYes101 (65h)Set Spectrum AnalyzerScaleSets the Spectrum Analyzer reference level and scale valueYes102 (66h)Set Spectrum AnalyzerMarkerSets position and on/off status of a Spectrum Analyzer markerYes103 (67h)Set Spectrum AnalyzerSingle LimitSets position and on/off status of Spectrum Analyzer single limit lineYes105 (69h)Set Spectrum Analyzer MaxHoldEnables or disables the Spectrum Analyzer Max Hold featureYesSite Master PM
Control Byte#Name106 (6Ah)Set Spectrum AnalyzerResolution Bandwidth FreqSets the Spectrum Analyzer resolution BW frequency (obsolete)Yes107 (6Bh)Set Spectrum AnalyzerVideo Bandwidth FreqSets the Spectrum Analyzer video BW frequency (obsolete)Yes108 (6Ch)Set Spectrum AnalyzerSweep ModeSets the Spectrum Analyzer sweep modeYes109 (6Dh)Set Spectrum AnalyzerMarker to PeakSets specified marker to peak value of the sweepYes110 (6Eh)Set Spectrum AnalyzerMarker to CenterSets the center frequency equal to the frequency of the specified markerYes111 (6Fh)Set Spectrum AnalyzerAttenuationSets the attenuation for the Site Master Spectrum Analyzer mode (obsolete)Yes112 (70h)Set VNA Segmented LimitLinesSets the position and On/Off status of the segmented limit lines for the VNAmodesYes113 (71h)Set Spectrum AnalyzerMultiple LimitSets the position and On/Off Status of a limit segment for the SPA modeYes114 (72h)Set Return SpectrumAnalyzer Sweep TimeIf this is enabled, the duration of the current sweep (in milliseconds) will bereturned as 4 bytes via the serial port at the end of the sweepYes115 (73h)Set Reference Level OffsetSets the value of the reference level offsetYes117 (0x75)Read Marker ValueReturns the fre
Site Master is the preferred cable and antenna analyzer of wireless providers, contractors and installers. Site Master S331D/S332D Cable and Antenna Analyzer MS2712 MS2712 MS2712 SiteMaster SpectrumMaster CellMaster S331D Site Master Site MasterMS2711D Spectrum Master Spectrum MT82
